diff --git a/stmhal/boards/PYBLITEV10/mpconfigboard.h b/stmhal/boards/PYBLITEV10/mpconfigboard.h
new file mode 100644
index 0000000000..e6f97c8201
--- /dev/null
+++ b/stmhal/boards/PYBLITEV10/mpconfigboard.h
@@ -0,0 +1,82 @@
+#define MICROPY_HW_BOARD_NAME "PYBLITEv1.0"
+#define MICROPY_HW_MCU_NAME "STM32F411RE"
+#define MICROPY_PY_SYS_PLATFORM "pyboard"
+
+#define MICROPY_HW_HAS_SWITCH (1)
+#define MICROPY_HW_HAS_SDCARD (1)
+#define MICROPY_HW_HAS_MMA7660 (1)
+#define MICROPY_HW_HAS_LIS3DSH (0)
+#define MICROPY_HW_HAS_LCD (1)
+#define MICROPY_HW_ENABLE_RNG (0)
+#define MICROPY_HW_ENABLE_RTC (1)
+#define MICROPY_HW_ENABLE_TIMER (1)
+#define MICROPY_HW_ENABLE_SERVO (1)
+#define MICROPY_HW_ENABLE_DAC (0)
+#define MICROPY_HW_ENABLE_SPI1 (1)
+#define MICROPY_HW_ENABLE_SPI2 (1)
+#define MICROPY_HW_ENABLE_SPI3 (0)
+#define MICROPY_HW_ENABLE_CAN (0)
+
+// HSE is 12MHz
+#define MICROPY_HW_CLK_PLLM (12)
+#define MICROPY_HW_CLK_PLLN (192)
+#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
+#define MICROPY_HW_CLK_PLLQ (4)
+#define MICROPY_HW_CLK_LAST_FREQ (1)
+
+// Pyboard lite has an optional 32kHz crystal
+#define MICROPY_HW_RTC_USE_LSE (1)
+#define MICROPY_HW_RTC_USE_US (0)
+#define MICROPY_HW_RTC_USE_CALOUT (1)
+
+// UART config
+#define MICROPY_HW_UART1_NAME "XB"
+#define MICROPY_HW_UART1_PORT (GPIOB)
+#define MICROPY_HW_UART1_PINS (GPIO_PIN_6 | GPIO_PIN_7)
+#define MICROPY_HW_UART2_NAME "XA"
+#define MICROPY_HW_UART2_PORT (GPIOA)
+#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3)
+#define MICROPY_HW_UART2_RTS (GPIO_PIN_1)
+#define MICROPY_HW_UART2_CTS (GPIO_PIN_0)
+#define MICROPY_HW_UART6_NAME "YA"
+#define MICROPY_HW_UART6_PORT (GPIOC)
+#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7)
+
+// I2C busses
+#define MICROPY_HW_I2C1_NAME "X"
+#define MICROPY_HW_I2C1_SCL (pin_B6)
+#define MICROPY_HW_I2C1_SDA (pin_B7)
+#define MICROPY_HW_I2C3_NAME "Y"
+#define MICROPY_HW_I2C3_SCL (pin_A8)
+#define MICROPY_HW_I2C3_SDA (pin_B8)
+
+// SPI busses
+#define MICROPY_HW_SPI1_NAME "X"
+#define MICROPY_HW_SPI2_NAME "Y"
+
+// USRSW has no pullup or pulldown, and pressing the switch makes the input go low
+#define MICROPY_HW_USRSW_PIN (pin_B3)
+#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP)
+#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
+#define MICROPY_HW_USRSW_PRESSED (0)
+
+// The pyboard has 4 LEDs
+#define MICROPY_HW_LED1 (pin_A13) // red
+#define MICROPY_HW_LED2 (pin_A14) // green
+#define MICROPY_HW_LED3 (pin_A15) // yellow
+#define MICROPY_HW_LED4 (pin_B4) // blue
+#define MICROPY_HW_LED4_PWM (1)
+#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)
+#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask)
+#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask)
+
+// SD card detect switch
+#define MICROPY_HW_SDCARD_DETECT_PIN (pin_B5)
+#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
+#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET)
+
+// USB config
+#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
+
+// MMA accelerometer config
+#define MICROPY_HW_MMA_AVDD_PIN (pin_A10)
diff --git a/stmhal/boards/PYBLITEV10/mpconfigboard.mk b/stmhal/boards/PYBLITEV10/mpconfigboard.mk
new file mode 100644
index 0000000000..71b3b19d65
--- /dev/null
+++ b/stmhal/boards/PYBLITEV10/mpconfigboard.mk
@@ -0,0 +1,4 @@
+MCU_SERIES = f4
+CMSIS_MCU = STM32F411xE
+AF_FILE = boards/stm32f411_af.csv
+LD_FILE = boards/stm32f411.ld
diff --git a/stmhal/boards/PYBLITEV10/pins.csv b/stmhal/boards/PYBLITEV10/pins.csv
new file mode 100644
index 0000000000..838587c1bc
--- /dev/null
+++ b/stmhal/boards/PYBLITEV10/pins.csv
@@ -0,0 +1,60 @@
+X1,PA2
+X2,PA3
+X3,PA0
+X4,PA1
+X5,PA4
+X6,PA5
+X7,PA6
+X8,PA7
+X9,PB6
+X10,PB7
+X11,PC4
+X12,PC5
+X13,Reset
+X14,GND
+X15,3.3V
+X16,VIN
+X17,PB3
+X18,PC13
+X19,PC0
+X20,PC1
+X21,PC2
+X22,PC3
+X23,A3.3V
+X24,AGND
+Y1,PC6
+Y2,PC7
+Y3,PB10
+Y4,PB9
+Y5,PB12
+Y6,PB13
+Y7,PB14
+Y8,PB15
+Y9,PA8
+Y10,PB8
+Y11,PB0
+Y12,PB1
+Y13,Reset
+Y14,GND
+Y15,3.3V
+Y16,VIN
+SW,PB3
+LED_BLUE,PB4
+LED_RED,PA13
+LED_GREEN,PA14
+LED_YELLOW,PA15
+MMA_AVDD,PA10
+MMA_INT,PB2
+SD_D0,PC8
+SD_D1,PC9
+SD_D2,PC10
+SD_D3,PC11
+SD_CMD,PD2
+SD_CK,PC12
+SD_SW,PB5
+USB_VBUS,PA9
+USB_DM,PA11
+USB_DP,PA12
+USB_ID,PA10
+OSC32_IN,PC14
+OSC32_OUT,PC15
diff --git a/stmhal/boards/PYBLITEV10/stm32f4xx_hal_conf.h b/stmhal/boards/PYBLITEV10/stm32f4xx_hal_conf.h
new file mode 100644
index 0000000000..1cf3d113db
--- /dev/null
+++ b/stmhal/boards/PYBLITEV10/stm32f4xx_hal_conf.h
@@ -0,0 +1,407 @@
+/**
+ ******************************************************************************
+ * @file stm32f4xx_hal_conf.h
+ * @author MCD Application Team
+ * @version V1.1.0
+ * @date 19-June-2014
+ * @brief HAL configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ * © COPYRIGHT(c) 2014 STMicroelectronics
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F4xx_HAL_CONF_H
+#define __STM32F4xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+#define USE_USB_FS
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+#define HAL_ADC_MODULE_ENABLED
+#define HAL_CAN_MODULE_ENABLED
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+#define HAL_DAC_MODULE_ENABLED
+/* #define HAL_DCMI_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+/* #define HAL_DMA2D_MODULE_ENABLED */
+/* #define HAL_ETH_MODULE_ENABLED */
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_PCCARD_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_SDRAM_MODULE_ENABLED */
+/* #define HAL_HASH_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_I2C_MODULE_ENABLED
+/* #define HAL_I2S_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+/* #define HAL_LTDC_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_RNG_MODULE_ENABLED
+#define HAL_RTC_MODULE_ENABLED
+/* #define HAL_SAI_MODULE_ENABLED */
+#define HAL_SD_MODULE_ENABLED
+#define HAL_SPI_MODULE_ENABLED
+#define HAL_TIM_MODULE_ENABLED
+#define HAL_UART_MODULE_ENABLED
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+#define HAL_PCD_MODULE_ENABLED
+/* #define HAL_HCD_MODULE_ENABLED */
+
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE ((uint32_t)12000000) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE ((uint32_t)40000)
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+/**
+ * @brief External clock source for I2S peripheral
+ * This value is used by the I2S HAL module to compute the I2S clock source
+ * frequency, this source is inserted directly through I2S_CKIN pad.
+ */
+#if !defined (EXTERNAL_CLOCK_VALUE)
+ #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY ((uint32_t)0x00) /*!< tick interrupt priority */
+#define USE_RTOS 0
+#define PREFETCH_ENABLE 1
+#define INSTRUCTION_CACHE_ENABLE 1
+#define DATA_CACHE_ENABLE 1
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1 */
+
+/* ################## Ethernet peripheral configuration ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0 2
+#define MAC_ADDR1 0
+#define MAC_ADDR2 0
+#define MAC_ADDR3 0
+#define MAC_ADDR4 0
+#define MAC_ADDR5 0
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
+#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
+#define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
+#define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
+
+/* Section 2: PHY configuration section */
+
+/* DP83848 PHY Address*/
+#define DP83848_PHY_ADDRESS 0x01
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY ((uint32_t)0x000000FF)
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF)
+
+#define PHY_READ_TO ((uint32_t)0x0000FFFF)
+#define PHY_WRITE_TO ((uint32_t)0x0000FFFF)
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */
+#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */
+
+#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
+#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
+#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
+#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
+#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
+#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
+#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
+
+#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
+#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
+#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
+
+/* Section 4: Extended PHY Registers */
+
+#define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */
+#define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */
+#define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */
+
+#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */
+#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */
+#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */
+
+#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */
+#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */
+
+#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */
+#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f4xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f4xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f4xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f4xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f4xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32f4xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f4xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32f4xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+ #include "stm32f4xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32f4xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32f4xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+ #include "stm32f4xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f4xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f4xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32f4xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f4xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f4xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f4xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f4xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f4xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f4xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F4xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/stmhal/boards/PYBV11/mpconfigboard.h b/stmhal/boards/PYBV11/mpconfigboard.h
new file mode 100644
index 0000000000..2951a9dbd9
--- /dev/null
+++ b/stmhal/boards/PYBV11/mpconfigboard.h
@@ -0,0 +1,94 @@
+#define MICROPY_HW_BOARD_NAME "PYBv1.1"
+#define MICROPY_HW_MCU_NAME "STM32F405RG"
+#define MICROPY_PY_SYS_PLATFORM "pyboard"
+
+#define MICROPY_HW_HAS_SWITCH (1)
+#define MICROPY_HW_HAS_SDCARD (1)
+#define MICROPY_HW_HAS_MMA7660 (1)
+#define MICROPY_HW_HAS_LIS3DSH (0)
+#define MICROPY_HW_HAS_LCD (1)
+#define MICROPY_HW_ENABLE_RNG (1)
+#define MICROPY_HW_ENABLE_RTC (1)
+#define MICROPY_HW_ENABLE_TIMER (1)
+#define MICROPY_HW_ENABLE_SERVO (1)
+#define MICROPY_HW_ENABLE_DAC (1)
+#define MICROPY_HW_ENABLE_SPI1 (1)
+#define MICROPY_HW_ENABLE_SPI2 (1)
+#define MICROPY_HW_ENABLE_SPI3 (0)
+#define MICROPY_HW_ENABLE_CAN (1)
+
+// HSE is 12MHz
+#define MICROPY_HW_CLK_PLLM (12)
+#define MICROPY_HW_CLK_PLLN (336)
+#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
+#define MICROPY_HW_CLK_PLLQ (7)
+#define MICROPY_HW_CLK_LAST_FREQ (1)
+
+// The pyboard has a 32kHz crystal for the RTC
+#define MICROPY_HW_RTC_USE_LSE (1)
+#define MICROPY_HW_RTC_USE_US (0)
+#define MICROPY_HW_RTC_USE_CALOUT (1)
+
+// UART config
+#define MICROPY_HW_UART1_NAME "XB"
+#define MICROPY_HW_UART1_PORT (GPIOB)
+#define MICROPY_HW_UART1_PINS (GPIO_PIN_6 | GPIO_PIN_7)
+#define MICROPY_HW_UART2_PORT (GPIOA)
+#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3)
+#define MICROPY_HW_UART2_RTS (GPIO_PIN_1)
+#define MICROPY_HW_UART2_CTS (GPIO_PIN_0)
+#define MICROPY_HW_UART3_NAME "YB"
+#define MICROPY_HW_UART3_PORT (GPIOB)
+#define MICROPY_HW_UART3_PINS (GPIO_PIN_10 | GPIO_PIN_11)
+#define MICROPY_HW_UART3_RTS (GPIO_PIN_14)
+#define MICROPY_HW_UART3_CTS (GPIO_PIN_13)
+#define MICROPY_HW_UART4_NAME "XA"
+#define MICROPY_HW_UART4_PORT (GPIOA)
+#define MICROPY_HW_UART4_PINS (GPIO_PIN_0 | GPIO_PIN_1)
+#define MICROPY_HW_UART6_NAME "YA"
+#define MICROPY_HW_UART6_PORT (GPIOC)
+#define MICROPY_HW_UART6_PINS (GPIO_PIN_6 | GPIO_PIN_7)
+
+// I2C busses
+#define MICROPY_HW_I2C1_NAME "X"
+#define MICROPY_HW_I2C1_SCL (pin_B6)
+#define MICROPY_HW_I2C1_SDA (pin_B7)
+#define MICROPY_HW_I2C2_NAME "Y"
+#define MICROPY_HW_I2C2_SCL (pin_B10)
+#define MICROPY_HW_I2C2_SDA (pin_B11)
+
+// SPI busses
+#define MICROPY_HW_SPI1_NAME "X"
+#define MICROPY_HW_SPI2_NAME "Y"
+
+// CAN busses
+#define MICROPY_HW_CAN1_NAME "YA" // CAN1 on RX,TX = Y3,Y4 = PB8,PB9
+#define MICROPY_HW_CAN2_NAME "YB" // CAN2 on RX,TX = Y5,Y6 = PB12,PB13
+
+// USRSW has no pullup or pulldown, and pressing the switch makes the input go low
+#define MICROPY_HW_USRSW_PIN (pin_B3)
+#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP)
+#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
+#define MICROPY_HW_USRSW_PRESSED (0)
+
+// The pyboard has 4 LEDs
+#define MICROPY_HW_LED1 (pin_A13) // red
+#define MICROPY_HW_LED2 (pin_A14) // green
+#define MICROPY_HW_LED3 (pin_A15) // yellow
+#define MICROPY_HW_LED4 (pin_B4) // blue
+#define MICROPY_HW_LED4_PWM (1)
+#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)
+#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask)
+#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask)
+
+// SD card detect switch
+#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8)
+#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
+#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET)
+
+// USB config
+#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
+#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
+
+// MMA accelerometer config
+#define MICROPY_HW_MMA_AVDD_PIN (pin_B5)
diff --git a/stmhal/boards/PYBV11/mpconfigboard.mk b/stmhal/boards/PYBV11/mpconfigboard.mk
new file mode 100644
index 0000000000..5734c66904
--- /dev/null
+++ b/stmhal/boards/PYBV11/mpconfigboard.mk
@@ -0,0 +1,4 @@
+MCU_SERIES = f4
+CMSIS_MCU = STM32F405xx
+AF_FILE = boards/stm32f405_af.csv
+LD_FILE = boards/stm32f405.ld
diff --git a/stmhal/boards/PYBV11/pins.csv b/stmhal/boards/PYBV11/pins.csv
new file mode 100644
index 0000000000..cee80a1aa1
--- /dev/null
+++ b/stmhal/boards/PYBV11/pins.csv
@@ -0,0 +1,59 @@
+X1,PA0
+X2,PA1
+X3,PA2
+X4,PA3
+X5,PA4
+X6,PA5
+X7,PA6
+X8,PA7
+X9,PB6
+X10,PB7
+X11,PC4
+X12,PC5
+X13,Reset
+X14,GND
+X15,3.3V
+X16,VIN
+X17,PB3
+X18,PC13
+X19,PC0
+X20,PC1
+X21,PC2
+X22,PC3
+X23,A3.3V
+X24,AGND
+Y1,PC6
+Y2,PC7
+Y3,PB8
+Y4,PB9
+Y5,PB12
+Y6,PB13
+Y7,PB14
+Y8,PB15
+Y9,PB10
+Y10,PB11
+Y11,PB0
+Y12,PB1
+Y13,Reset
+Y14,GND
+Y15,3.3V
+Y16,VIN
+SW,PB3
+LED_RED,PA13
+LED_GREEN,PA14
+LED_YELLOW,PA15
+LED_BLUE,PB4
+MMA_INT,PB2
+MMA_AVDD,PB5
+SD_D0,PC8
+SD_D1,PC9
+SD_D2,PC10
+SD_D3,PC11
+SD_CMD,PD2
+SD_CK,PC12
+SD,PA8
+SD_SW,PA8
+USB_VBUS,PA9
+USB_ID,PA10
+USB_DM,PA11
+USB_DP,PA12
diff --git a/stmhal/boards/PYBV11/stm32f4xx_hal_conf.h b/stmhal/boards/PYBV11/stm32f4xx_hal_conf.h
new file mode 100644
index 0000000000..bdd7ef5634
--- /dev/null
+++ b/stmhal/boards/PYBV11/stm32f4xx_hal_conf.h
@@ -0,0 +1,407 @@
+/**
+ ******************************************************************************
+ * @file stm32f4xx_hal_conf.h
+ * @author MCD Application Team
+ * @version V1.1.0
+ * @date 19-June-2014
+ * @brief HAL configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ * © COPYRIGHT(c) 2014 STMicroelectronics
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F4xx_HAL_CONF_H
+#define __STM32F4xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+#define USE_USB_FS
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+#define HAL_ADC_MODULE_ENABLED
+#define HAL_CAN_MODULE_ENABLED
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+#define HAL_DAC_MODULE_ENABLED
+/* #define HAL_DCMI_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+/* #define HAL_DMA2D_MODULE_ENABLED */
+/* #define HAL_ETH_MODULE_ENABLED */
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_PCCARD_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_SDRAM_MODULE_ENABLED */
+/* #define HAL_HASH_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_I2C_MODULE_ENABLED
+#define HAL_I2S_MODULE_ENABLED
+/* #define HAL_IWDG_MODULE_ENABLED */
+/* #define HAL_LTDC_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_RNG_MODULE_ENABLED
+#define HAL_RTC_MODULE_ENABLED
+/* #define HAL_SAI_MODULE_ENABLED */
+#define HAL_SD_MODULE_ENABLED
+#define HAL_SPI_MODULE_ENABLED
+#define HAL_TIM_MODULE_ENABLED
+#define HAL_UART_MODULE_ENABLED
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+#define HAL_PCD_MODULE_ENABLED
+/* #define HAL_HCD_MODULE_ENABLED */
+
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE ((uint32_t)12000000) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE ((uint32_t)40000)
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature. */
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+/**
+ * @brief External clock source for I2S peripheral
+ * This value is used by the I2S HAL module to compute the I2S clock source
+ * frequency, this source is inserted directly through I2S_CKIN pad.
+ */
+#if !defined (EXTERNAL_CLOCK_VALUE)
+ #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY ((uint32_t)0x00) /*!< tick interrupt priority */
+#define USE_RTOS 0
+#define PREFETCH_ENABLE 1
+#define INSTRUCTION_CACHE_ENABLE 1
+#define DATA_CACHE_ENABLE 1
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1 */
+
+/* ################## Ethernet peripheral configuration ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0 2
+#define MAC_ADDR1 0
+#define MAC_ADDR2 0
+#define MAC_ADDR3 0
+#define MAC_ADDR4 0
+#define MAC_ADDR5 0
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
+#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
+#define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
+#define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
+
+/* Section 2: PHY configuration section */
+
+/* DP83848 PHY Address*/
+#define DP83848_PHY_ADDRESS 0x01
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY ((uint32_t)0x000000FF)
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF)
+
+#define PHY_READ_TO ((uint32_t)0x0000FFFF)
+#define PHY_WRITE_TO ((uint32_t)0x0000FFFF)
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */
+#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */
+
+#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
+#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
+#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
+#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
+#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
+#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
+#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
+
+#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
+#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
+#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
+
+/* Section 4: Extended PHY Registers */
+
+#define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */
+#define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */
+#define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */
+
+#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */
+#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */
+#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */
+
+#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */
+#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */
+
+#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */
+#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f4xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f4xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f4xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f4xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f4xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32f4xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+ #include "stm32f4xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f4xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32f4xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+ #include "stm32f4xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32f4xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32f4xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+ #include "stm32f4xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f4xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f4xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+ #include "stm32f4xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f4xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f4xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f4xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32f4xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f4xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f4xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f4xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f4xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f4xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f4xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f4xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f4xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f4xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F4xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/