Add internal display definitions, fails at startup

ports/stm32f4/boards/meowbit_v121/board.c

@@ -27,7 +27,89 @@
 #include "boards/board.h"
 #include "mpconfigboard.h"
 
+#include "shared-bindings/board/__init__.h"
+#include "shared-bindings/displayio/FourWire.h"
+#include "shared-module/displayio/__init__.h"
+#include "shared-module/displayio/mipi_constants.h"
+#include "shared-bindings/busio/SPI.h"
+
+#include "supervisor/spi_flash_api.h"
+
+#include "tick.h"
+
+displayio_fourwire_obj_t board_display_obj;
+
+#define DELAY 0x80
+
+uint8_t display_init_sequence[] = {
+    0x01, 0 | DELAY, 150, // SWRESET
+	0x11, 0 | DELAY, 255, // SLPOUT
+	0xb1, 3, 0x01, 0x2C, 0x2D, // _FRMCTR1
+	0xb2, 3, 0x01, 0x2C, 0x2D, //
+	0xb3, 6, 0x01, 0x2C, 0x2D, 0x01, 0x2C, 0x2D,
+	0xb4, 1, 0x07, // _INVCTR line inversion
+	0xc0, 3, 0xa2, 0x02, 0x84, // _PWCTR1 GVDD = 4.7V, 1.0uA
+	0xc1, 1, 0xc5, // _PWCTR2 VGH=14.7V, VGL=-7.35V
+	0xc2, 2, 0x0a, 0x00, // _PWCTR3 Opamp current small, Boost frequency
+	0xc3, 2, 0x8a, 0x2a,
+	0xc4, 2, 0x8a, 0xee,
+	0xc5, 1, 0x0e, // _VMCTR1 VCOMH = 4V, VOML = -1.1V
+	0x20, 0, // _INVOFF //MISMATCh 0x2a vs 0x20
+	0x36, 1, 0x18, // _MADCTL bottom to top refresh
+	// 1 clk cycle nonoverlap, 2 cycle gate rise, 3 sycle osc equalie,
+	// fix on VTL
+	0x3a, 1, 0x05, // COLMOD - 16bit color
+	0xe0, 0x10, 0x02, 0x1c, 0x07, 0x12,
+				0x37, 0x32, 0x29, 0x2d,
+				0x29, 0x25, 0x2B, 0x39, 
+				0x00, 0x01, 0x03, 0x10, // _GMCTRP1 Gamma
+	0xe1, 0x10, 0x03, 0x1d, 0x07, 0x06,
+				0x2E, 0x2C, 0x29, 0x2D,
+				0x2E, 0x2E, 0x37, 0x3F,
+				0x00, 0x00, 0x02, 0x10, // _GMCTRN1
+	0x13, 0 | DELAY, 10, // _NORON
+	0x29, 0 | DELAY, 100, // _DISPON
+};
+
 void board_init(void) {
+    displayio_fourwire_obj_t* bus = &displays[0].fourwire_bus;
+    bus->base.type = &displayio_fourwire_type;
+    busio_spi_obj_t *internal_spi = &spi;
+    common_hal_displayio_fourwire_construct(bus,
+        internal_spi,
+        &pin_PA08, // Command or data
+        &pin_PB12, // Chip select
+        &pin_PB10, // Reset
+        24000000);
+
+    displayio_display_obj_t* display = &displays[0].display;
+    display->base.type = &displayio_display_type;
+    common_hal_displayio_display_construct(display,
+        bus,
+        160, // Width
+        128, // Height
+        0, // column start
+        0, // row start
+        90, // rotation
+        16, // Color depth
+        false, // Grayscale
+        false, // Pixels in a byte share a row. Only used for depth < 8
+        1, // bytes per cell. Only valid for depths < 8
+        false, // reverse_pixels_in_byte. Only valid for depths < 8
+        MIPI_COMMAND_SET_COLUMN_ADDRESS, // Set column command
+        MIPI_COMMAND_SET_PAGE_ADDRESS, // Set row command
+        MIPI_COMMAND_WRITE_MEMORY_START, // Write memory command
+        0x37, // set vertical scroll command
+        display_init_sequence,
+        sizeof(display_init_sequence),
+        &pin_PB03,
+        NO_BRIGHTNESS_COMMAND,
+        1.0f, // brightness (ignored)
+        true, // auto_brightness
+        false, // single_byte_bounds
+        false, // data_as_commands
+        true, // auto_refresh
+        60); // native_frames_per_second
 }
 
 bool board_requests_safe_mode(void) {

ports/stm32f4/boards/meowbit_v121/mpconfigboard.h

@@ -37,7 +37,7 @@
 
 #define BOARD_OSC_DIV 12
 #define BOARD_NO_VBUS_SENSE
-#define BOARD_VTOR_DEFER //Leave VTOR relocation to bootloader
+// #define BOARD_VTOR_DEFER //Leave VTOR relocation to bootloader
 #define BOARD_USE_INTERNAL_SPI
 
 // On-board flash

ports/stm32f4/boards/meowbit_v121/mpconfigboard.mk

@@ -9,7 +9,7 @@ EXTERNAL_FLASH_DEVICE_COUNT = 1
 EXTERNAL_FLASH_DEVICES = W25Q16JV_IQ
 LONGINT_IMPL = MPZ
 
-BOOTLOADER_OFFSET = 0x8010000
+# BOOTLOADER_OFFSET = 0x8010000
 
 # INTERNAL_FLASH_FILESYSTEM = 1
 # LONGINT_IMPL = NONE
@@ -19,5 +19,5 @@ MCU_VARIANT = stm32f4
 MCU_SUB_VARIANT = stm32f401xe
 MCU_PACKAGE = 64
 CMSIS_MCU = STM32F401xE
-LD_FILE = boards/STM32F401_boot.ld 
-# LD_FILE = boards/STM32F401_fs.ld #use for internal flash
+# LD_FILE = boards/STM32F401_boot.ld 
+LD_FILE = boards/STM32F401_fs.ld #use for internal flash

ports/stm32f4/boards/meowbit_v121/pins.c

@@ -1,6 +1,8 @@
 #include "shared-bindings/board/__init__.h"
 #include "supervisor/spi_flash_api.h"
 
+#include "shared-module/displayio/__init__.h"
+
 STATIC const mp_rom_map_elem_t board_module_globals_table[] = {
     { MP_ROM_QSTR(MP_QSTR_LED_RED), MP_ROM_PTR(&pin_PB04) },
     { MP_ROM_QSTR(MP_QSTR_LED_GREEN), MP_ROM_PTR(&pin_PB05) },
@@ -61,5 +63,7 @@ STATIC const mp_rom_map_elem_t board_module_globals_table[] = {
     { MP_ROM_QSTR(MP_QSTR_P3), MP_ROM_PTR(&pin_PB00) },
 
     { MP_ROM_QSTR(MP_QSTR_INTERNAL_SPI), MP_ROM_PTR(&spi) },
+
+    { MP_ROM_QSTR(MP_QSTR_DISPLAY), MP_ROM_PTR(&displays[0].display)},
 };
 MP_DEFINE_CONST_DICT(board_module_globals, board_module_globals_table);