Updates for Makerfabs TFT 7" touch dotclock panel

ports/espressif/boards/makerfabs_tft7/mpconfigboard.mk

@@ -1,5 +1,5 @@
-USB_VID = 0x239A
+USB_VID = 0x303A
-USB_PID = 0x814A
+USB_PID = 0x81BF
 USB_PRODUCT = "MakerFabs-ESP32-S3-Parallel-TFT-With-Touch-7inch"
 USB_MANUFACTURER = "MakerFabs"
 
@@ -14,3 +14,13 @@ CIRCUITPY_ESP_PSRAM_MODE = opi
 CIRCUITPY_ESP_PSRAM_FREQ = 80m
 
 CIRCUITPY_DOTCLOCKFRAMEBUFFER = 1
+
+# To build with USB disabled allowing access to I2S pins
+#CIRCUITPY_CREATOR_ID = 0x000C303A
+#CIRCUITPY_CREATION_ID = 0x00A30001
+#CIRCUITPY_USB=0
+#CIRCUITPY_BUILD_EXTENSIONS = bin,uf2
+#UF2_BOOTLOADER = 1
+#CIRCUITPY_WIFI=1
+#CIRCUITPY_WEB_WORKFLOW=1
+#OPTIMIZATION_FLAGS = -Os

ports/espressif/boards/makerfabs_tft7/pins.c

@@ -67,20 +67,43 @@ STATIC const mp_rom_map_elem_t timings800_table[] = {
 };
 MP_DEFINE_CONST_DICT(timings800_dict, timings800_table);
 
+STATIC const mp_rom_map_elem_t timings1024_table[] = {
+    { MP_ROM_QSTR(MP_QSTR_frequency), MP_ROM_INT(10000000) }, // nominal 16MHz, but display is unstable/tears at that frequency
+    { MP_ROM_QSTR(MP_QSTR_width), MP_ROM_INT(1024) },
+    { MP_ROM_QSTR(MP_QSTR_height), MP_ROM_INT(600) },
+    { MP_ROM_QSTR(MP_QSTR_hsync_pulse_width), MP_ROM_INT(30) },
+    { MP_ROM_QSTR(MP_QSTR_hsync_front_porch), MP_ROM_INT(210) },
+    { MP_ROM_QSTR(MP_QSTR_hsync_back_porch), MP_ROM_INT(16) },
+    { MP_ROM_QSTR(MP_QSTR_hsync_idle_low), MP_ROM_FALSE },
+    { MP_ROM_QSTR(MP_QSTR_vsync_pulse_width), MP_ROM_INT(13) },
+    { MP_ROM_QSTR(MP_QSTR_vsync_front_porch), MP_ROM_INT(22) },
+    { MP_ROM_QSTR(MP_QSTR_vsync_back_porch), MP_ROM_INT(10) },
+    { MP_ROM_QSTR(MP_QSTR_vsync_idle_low), MP_ROM_FALSE },
+    { MP_ROM_QSTR(MP_QSTR_de_idle_high), MP_ROM_FALSE },
+    { MP_ROM_QSTR(MP_QSTR_pclk_active_high), MP_ROM_FALSE },
+    { MP_ROM_QSTR(MP_QSTR_pclk_idle_high), MP_ROM_FALSE },
+};
+MP_DEFINE_CONST_DICT(timings1024_dict, timings1024_table);
+
 STATIC const mp_rom_map_elem_t board_module_globals_table[] = {
     CIRCUITPYTHON_BOARD_DICT_STANDARD_ITEMS
 
     { MP_ROM_QSTR(MP_QSTR_TFT_PINS), MP_ROM_PTR(&tft_pins_dict) },
     { MP_ROM_QSTR(MP_QSTR_TFT_TIMINGS), MP_ROM_PTR(&timings800_dict) },
+    { MP_ROM_QSTR(MP_QSTR_TFT_TIMINGS800), MP_ROM_PTR(&timings800_dict) },
+    { MP_ROM_QSTR(MP_QSTR_TFT_TIMINGS1024), MP_ROM_PTR(&timings1024_dict) },
     { MP_ROM_QSTR(MP_QSTR_TFT_BACKLIGHT), MP_ROM_PTR(&pin_GPIO10) },
 
     // GPIO pins available on Mabee connector port (also shared with I2S & USB D+/D-)
     { MP_ROM_QSTR(MP_QSTR_GPIO20), MP_ROM_PTR(&pin_GPIO20) },
     { MP_ROM_QSTR(MP_QSTR_GPIO19), MP_ROM_PTR(&pin_GPIO19) },
 
+    // I2S pins are shared with USB D+/D-, these are only useful if USB is disabled
+    #if CIRCUITPY_USB == 0
     { MP_ROM_QSTR(MP_QSTR_I2S_BIT_CLOCK), MP_ROM_PTR(&pin_GPIO20) },
     { MP_ROM_QSTR(MP_QSTR_I2S_WORD_SELECT), MP_ROM_PTR(&pin_GPIO2) },
     { MP_ROM_QSTR(MP_QSTR_I2S_DATA), MP_ROM_PTR(&pin_GPIO19) },
+    #endif
 
     { MP_ROM_QSTR(MP_QSTR_TX), MP_ROM_PTR(&pin_GPIO43) },
     { MP_ROM_QSTR(MP_QSTR_RX), MP_ROM_PTR(&pin_GPIO44) },
@@ -89,16 +112,16 @@ STATIC const mp_rom_map_elem_t board_module_globals_table[] = {
     { MP_ROM_QSTR(MP_QSTR_SDA), MP_ROM_PTR(&pin_GPIO17) },
     { MP_ROM_QSTR(MP_QSTR_TOUCH_RESET), MP_ROM_PTR(&pin_GPIO38) },
 
-    { MP_ROM_QSTR(MP_QSTR_SDIO_CMD), MP_ROM_PTR(&pin_GPIO11) },
+    // IO10 <> SD_CS is cut at factory (non-placed resistor position R34) and pulled up.
-    { MP_ROM_QSTR(MP_QSTR_SDIO_D0), MP_ROM_PTR(&pin_GPIO13) },
+    // Permanent SDIO 1-bit mode?
-    { MP_ROM_QSTR(MP_QSTR_SDIO_CLK), MP_ROM_PTR(&pin_GPIO12) },
+    // Until SDIO 1-bit mode is support on Espressif ports these pins aren't useful
+    // { MP_ROM_QSTR(MP_QSTR_SDIO_CMD), MP_ROM_PTR(&pin_GPIO11) },
+    // { MP_ROM_QSTR(MP_QSTR_SDIO_D0), MP_ROM_PTR(&pin_GPIO13) },
+    // { MP_ROM_QSTR(MP_QSTR_SDIO_CLK), MP_ROM_PTR(&pin_GPIO12) },
 
     // boot mode button can be used in SW as well
     { MP_ROM_QSTR(MP_QSTR_BUTTON), MP_ROM_PTR(&pin_GPIO1) },
 
-    // IO10 <> SD_CS is cut at factory (non-placed resistor position R34) and pulled up.
-    // Permanent SDIO 1-bit mode?
-
     { MP_ROM_QSTR(MP_QSTR_I2C), MP_ROM_PTR(&board_i2c_obj) },
 };
 MP_DEFINE_CONST_DICT(board_module_globals, board_module_globals_table);

ports/espressif/common-hal/microcontroller/Pin.c

@@ -173,12 +173,15 @@ static const uint64_t pin_mask_reset_forbidden =
     GPIO_SEL_23 |
     GPIO_SEL_24 |
     #endif
-    #endif // ESP32C6
+    #endif // ESP32H2
 
     #if defined(CONFIG_IDF_TARGET_ESP32S2) || defined(CONFIG_IDF_TARGET_ESP32S3)
-    // Never ever reset pins used to communicate with SPI flash and PSRAM.
+    #if CIRCUITPY_USB
+    // Never ever reset USB pins.
     GPIO_SEL_19 |         // USB D-
     GPIO_SEL_20 |         // USB D+
+    #endif
+    // Never ever reset pins used to communicate with SPI flash and PSRAM.
     #if defined(CONFIG_ESP32_SPIRAM_SUPPORT) || defined(CONFIG_ESP32S2_SPIRAM_SUPPORT) || defined(CONFIG_ESP32S3_SPIRAM_SUPPORT)
     // Note ESP32-C3 does not have SPIRAM support.
     // Board uses PSRAM, and needs another chip select.
@@ -198,11 +201,6 @@ static const uint64_t pin_mask_reset_forbidden =
     GPIO_SEL_36 |         // SPIIO7
     GPIO_SEL_37 |         // SPIDQS
     #endif
-    #if CIRCUITPY_USB
-    // Never ever reset USB pins.
-    GPIO_SEL_19 |         // USB D-
-    GPIO_SEL_20 |         // USB D+
-    #endif
     #if defined(CONFIG_ESP_CONSOLE_UART_DEFAULT) && CONFIG_ESP_CONSOLE_UART_DEFAULT && CONFIG_ESP_CONSOLE_UART_NUM == 0
     // Don't reset/use the IDF UART console.
     GPIO_SEL_43 | // UART TX