esp32/boards: Update board and deploy metadata for UM_xxx boards.

ports/esp32/boards/UM_FEATHERS2/board.json

@@ -1,6 +1,6 @@
 {
     "deploy": [
-        "../deploy_s2.md"
+        "deploy.md"
     ],
     "docs": "",
     "features": [
@@ -8,7 +8,12 @@
         "Feather",
         "Battery Charging",
         "STEMMA QT/QWIIC",
-        "USB-C"
+        "USB-C",
+        "RGB LED",
+        "SPIRAM"
+    ],
+    "features_non_filterable": [
+        "Second LDO"
     ],
     "id": "featherS2",
     "images": [

ports/esp32/boards/UM_FEATHERS2/board.md

@@ -0,0 +1,2 @@
+The following files are daily firmware for the FeatherS2. This firmware is
+compiled using ESP-IDF v4.3 or later.

ports/esp32/boards/UM_FEATHERS2/deploy.md

@@ -0,0 +1,50 @@
+Program your board using the esptool.py program, found [here](https://github.com/espressif/esptool).
+
+To flash or erase your FeatherS2, you have to first put it into download mode.
+To do this, follow these steps:
+
+- Press and hold the [BOOT] button
+- Press and release the [RESET] button
+- Release the [BOOT] button
+
+Now the board is in download mode and the native USB will have enumerated as a serial device.
+
+If you are putting MicroPython on your board for the first time then you should
+first erase the entire flash using:
+
+### Linux
+```bash
+esptool.py --chip esp32s2 --port /dev/ttyACM0 erase_flash
+```
+
+### Mac
+```bash
+esptool.py --chip esp32s2 --port /dev/cu.usbmodem01 erase_flash
+```
+
+### Windows
+Change (X) to whatever COM port is being used by the board
+```bash
+esptool --chip esp32s2 --port COM(X) erase_flash
+```
+
+Now download the version of the firmware you would like to install from the options
+below, then use the following command to program the firmware starting at address
+0x1000, remembering to replace `feathers2-micropython-firmware-version.bin` with the
+name of the firmware you just downloaded:
+
+### Linux
+```bash
+esptool.py --chip esp32s2 --port /dev/ttyACM0 write_flash -z 0x1000 feathers2-micropython-firmware-version.bin
+```
+
+### Mac
+```bash
+esptool.py --chip esp32s2 --port /dev/cu.usbmodem01 write_flash -z 0x1000 feathers2-micropython-firmware-version.bin
+```
+
+### Windows
+Change (X) to whatever COM port is being used by the board
+```bash
+esptool --chip esp32s2 --port COM(X) write_flash -z 0x1000 feathers2-micropython-firmware-version.bin
+```

ports/esp32/boards/UM_FEATHERS2NEO/board.json

@@ -1,6 +1,6 @@
 {
     "deploy": [
-        "../deploy_s2.md"
+        "deploy.md"
     ],
     "docs": "",
     "features": [
@@ -9,10 +9,16 @@
         "Battery Charging",
         "STEMMA QT/QWIIC",
         "USB-C",
-        "Neopixels"
+        "RGB LED",
+        "SPIRAM"
+    ],
+    "features_non_filterable": [
+        "5x5 RGB LED Matrix"
     ],
     "id": "featherS2neo",
-    "images": [],
+    "images": [
+        "FeatherS2_Neo_White_Product2.jpg"
+    ],
     "mcu": "esp32s2",
     "product": "Feather S2 Neo",
     "thumbnail": "",

ports/esp32/boards/UM_FEATHERS2NEO/board.md

@@ -0,0 +1,2 @@
+The following files are daily firmware for the FeatherS2 Neo. This firmware is
+compiled using ESP-IDF v4.3 or later.

ports/esp32/boards/UM_FEATHERS2NEO/deploy.md

@@ -0,0 +1,50 @@
+Program your board using the esptool.py program, found [here](https://github.com/espressif/esptool).
+
+To flash or erase your FeatherS2 Neo, you have to first put it into download mode.
+To do this, follow these steps:
+
+- Press and hold the [BOOT] button
+- Press and release the [RESET] button
+- Release the [BOOT] button
+
+Now the board is in download mode and the native USB will have enumerated as a serial device.
+
+If you are putting MicroPython on your board for the first time then you should
+first erase the entire flash using:
+
+### Linux
+```bash
+esptool.py --chip esp32s2 --port /dev/ttyACM0 erase_flash
+```
+
+### Mac
+```bash
+esptool.py --chip esp32s2 --port /dev/cu.usbmodem01 erase_flash
+```
+
+### Windows
+Change (X) to whatever COM port is being used by the board
+```bash
+esptool --chip esp32s2 --port COM(X) erase_flash
+```
+
+Now download the version of the firmware you would like to install from the options below,
+then use the following command to program the firmware starting at address 0x1000,
+remembering to replace `feathers2neo-micropython-firmware-version.bin` with the name of
+the firmware you just downloaded:
+
+### Linux
+```bash
+esptool.py --chip esp32s2 --port /dev/ttyACM0 write_flash -z 0x1000 feathers2neo-micropython-firmware-version.bin
+```
+
+### Mac
+```bash
+esptool.py --chip esp32s2 --port /dev/cu.usbmodem01 write_flash -z 0x1000 feathers2neo-micropython-firmware-version.bin
+```
+
+### Windows
+Change (X) to whatever COM port is being used by the board
+```bash
+esptool --chip esp32s2 --port COM(X) write_flash -z 0x1000 feathers2-feathers2neo-firmware-version.bin
+```

ports/esp32/boards/UM_TINYPICO/board.json

@@ -1,9 +1,19 @@
 {
     "deploy": [
-        "../deploy.md"
+        "deploy.md"
     ],
     "docs": "",
-    "features": [],
+    "features": [
+        "BLE",
+        "WiFi",
+        "Battery Charging",
+        "USB-C",
+        "RGB LED",
+        "SPIRAM"
+    ],
+    "features_non_filterable": [
+        "TinyPICO Compatible"
+    ],
     "id": "tinypico",
     "images": [
         "tinypico-v2-both.jpg"

ports/esp32/boards/UM_TINYPICO/board.md

@@ -0,0 +1,3 @@
+The following files are daily firmware for the TinyPICO. This firmware is compiled
+using ESP-IDF v4.2 or later.  Some older releases are also provided that are
+compiled with ESP-IDF v3.x.

ports/esp32/boards/UM_TINYPICO/deploy.md

@@ -0,0 +1,46 @@
+Program your board using the esptool.py program, found [here](https://github.com/espressif/esptool).
+
+Your TinyPICO has an auto-reset circuit on it, so there is no need to put it into a
+download mode first to erase or flash it.
+
+If you are putting MicroPython on your board for the first time then you should
+first erase the entire flash using:
+
+### Linux
+```bash
+esptool.py --chip esp32 --port /dev/ttyUSB0 erase_flash
+```
+
+### Mac
+```bash
+esptool.py --chip esp32 --port /dev/tty.SLAB_USBtoUART erase_flash
+```
+
+### Windows
+Change (X) to whatever COM port is being used by the board
+```bash
+esptool --chip esp32 --port COM(X) erase_flash
+```
+
+Now download the version of the firmware you would like to install from the options below,
+then use the following command to program the firmware starting at address 0x1000,
+remembering to replace `tinypico-micropython-firmware-version.bin` with the name of the
+firmware you just downloaded:
+
+From then on program the firmware starting at address 0x1000:
+
+### Linux
+```bash
+esptool.py --chip esp32 --port /dev/ttyUSB0 --baud 912600 write_flash -z 0x1000 tinypico-micropython-firmware-version.bin
+```
+
+### Mac
+```bash
+esptool.py --chip esp32 --port /dev/tty.SLAB_USBtoUART --baud 912600 write_flash -z 0x1000 tinypico-micropython-firmware-version.bin
+```
+
+### Windows
+Change (X) to whatever COM port is being used by the board
+```bash
+esptool --chip esp32 --port COM(X) --baud 912600 write_flash -z 0x1000 tinypico-micropython-firmware-version.bin
+```

ports/esp32/boards/UM_TINYS2/board.json

@@ -1,11 +1,19 @@
 {
     "deploy": [
-        "../deploy_s2.md"
+        "deploy.md"
     ],
     "docs": "",
     "features": [
         "WiFi",
         "USB-C"
+        "Battery Charging",
+        "STEMMA QT/QWIIC",
+        "USB-C",
+        "RGB LED",
+        "SPIRAM"
+    ],
+    "features_non_filterable": [
+        "TinyPICO Compatible"
     ],
     "id": "tinys2",
     "images": [

ports/esp32/boards/UM_TINYS2/board.md

@@ -0,0 +1,2 @@
+The following files are daily firmware for the TinyS2. This firmware is compiled
+using ESP-IDF v4.3 or later.

ports/esp32/boards/UM_TINYS2/deploy.md

@@ -0,0 +1,50 @@
+Program your board using the esptool.py program, found [here](https://github.com/espressif/esptool).
+
+To flash or erase your TinyS2, you have to first put it into download mode.
+To do this, follow these steps:
+
+- Press and hold the [BOOT] button
+- Press and release the [RESET] button
+- Release the [BOOT] button
+
+Now the board is in download mode and the native USB will have enumerated as a serial device.
+
+If you are putting MicroPython on your board for the first time then you should
+first erase the entire flash using:
+
+### Linux
+```bash
+esptool.py --chip esp32s2 --port /dev/ttyACM0 erase_flash
+```
+
+### Mac
+```bash
+esptool.py --chip esp32s2 --port /dev/cu.usbmodem01 erase_flash
+```
+
+#### Windows
+Change (X) to whatever COM port is being used by the board
+```bash
+esptool --chip esp32s2 --port COM(X) erase_flash
+```
+
+Now download the version of the firmware you would like to install from the options below,
+then use the following command to program the firmware starting at address 0x1000,
+remembering to replace `tinys2-micropython-firmware-version.bin` with the name of the
+firmware you just downloaded:
+
+#### Linux
+```bash
+esptool.py --chip esp32s2 --port /dev/ttyACM0 write_flash -z 0x1000 tinys2-micropython-firmware-version.bin
+```
+
+#### Mac
+```bash
+esptool.py --chip esp32s2 --port /dev/cu.usbmodem01 write_flash -z 0x1000 tinys2-micropython-firmware-version.bin
+```
+
+#### Windows
+Change (X) to whatever COM port is being used by the board
+```bash
+esptool --chip esp32s2 --port COM(X) write_flash -z 0x1000 tinys2-micropython-firmware-version.bin
+```