Merge remote-tracking branch 'origin/main' into main
This commit is contained in:
commit
491badc766
@ -1535,6 +1535,12 @@ msgstr ""
|
||||
msgid "No out in program"
|
||||
msgstr ""
|
||||
|
||||
#: ports/atmel-samd/common-hal/busio/I2C.c ports/esp32s2/common-hal/busio/I2C.c
|
||||
#: ports/mimxrt10xx/common-hal/busio/I2C.c ports/nrf/common-hal/busio/I2C.c
|
||||
#: ports/raspberrypi/common-hal/busio/I2C.c
|
||||
msgid "No pull up found on SDA or SCL; check your wiring"
|
||||
msgstr ""
|
||||
|
||||
#: shared-module/touchio/TouchIn.c
|
||||
msgid "No pulldown on pin; 1Mohm recommended"
|
||||
msgstr ""
|
||||
@ -1866,12 +1872,6 @@ msgstr ""
|
||||
msgid "SD card CSD format not supported"
|
||||
msgstr ""
|
||||
|
||||
#: ports/atmel-samd/common-hal/busio/I2C.c ports/esp32s2/common-hal/busio/I2C.c
|
||||
#: ports/mimxrt10xx/common-hal/busio/I2C.c ports/nrf/common-hal/busio/I2C.c
|
||||
#: ports/raspberrypi/common-hal/busio/I2C.c
|
||||
msgid "SDA or SCL needs a pull up"
|
||||
msgstr ""
|
||||
|
||||
#: ports/stm/common-hal/sdioio/SDCard.c
|
||||
#, c-format
|
||||
msgid "SDIO GetCardInfo Error %d"
|
||||
|
@ -11,14 +11,5 @@ LONGINT_IMPL = NONE
|
||||
CIRCUITPY_FULL_BUILD = 0
|
||||
|
||||
SUPEROPT_GC = 0
|
||||
|
||||
CFLAGS_BOARD = --param max-inline-insns-auto=15
|
||||
ifeq ($(TRANSLATION), zh_Latn_pinyin)
|
||||
RELEASE_NEEDS_CLEAN_BUILD = 1
|
||||
CFLAGS_INLINE_LIMIT = 35
|
||||
endif
|
||||
ifeq ($(TRANSLATION), de_DE)
|
||||
RELEASE_NEEDS_CLEAN_BUILD = 1
|
||||
CFLAGS_INLINE_LIMIT = 35
|
||||
SUPEROPT_VM = 0
|
||||
endif
|
||||
CFLAGS_INLINE_LIMIT = 45
|
||||
|
@ -97,7 +97,7 @@ void common_hal_busio_i2c_construct(busio_i2c_obj_t *self,
|
||||
if (!gpio_get_pin_level(sda->number) || !gpio_get_pin_level(scl->number)) {
|
||||
reset_pin_number(sda->number);
|
||||
reset_pin_number(scl->number);
|
||||
mp_raise_RuntimeError(translate("SDA or SCL needs a pull up"));
|
||||
mp_raise_RuntimeError(translate("No pull up found on SDA or SCL; check your wiring"));
|
||||
}
|
||||
#endif
|
||||
|
||||
|
@ -85,7 +85,7 @@ void common_hal_busio_i2c_construct(busio_i2c_obj_t *self,
|
||||
if (gpio_get_level(sda->number) == 0 || gpio_get_level(scl->number) == 0) {
|
||||
reset_pin_number(sda->number);
|
||||
reset_pin_number(scl->number);
|
||||
mp_raise_RuntimeError(translate("SDA or SCL needs a pull up"));
|
||||
mp_raise_RuntimeError(translate("No pull up found on SDA or SCL; check your wiring"));
|
||||
}
|
||||
#endif
|
||||
|
||||
|
@ -110,7 +110,7 @@ void common_hal_busio_i2c_construct(busio_i2c_obj_t *self,
|
||||
if( !GPIO_PinRead(sda->gpio, sda->number) || !GPIO_PinRead(scl->gpio, scl->number)) {
|
||||
common_hal_reset_pin(sda);
|
||||
common_hal_reset_pin(scl);
|
||||
mp_raise_RuntimeError(translate("SDA or SCL needs a pull up"));
|
||||
mp_raise_RuntimeError(translate("No pull up found on SDA or SCL; check your wiring"));
|
||||
}
|
||||
#endif
|
||||
|
||||
|
@ -131,7 +131,7 @@ void common_hal_busio_i2c_construct(busio_i2c_obj_t *self, const mcu_pin_obj_t *
|
||||
if (!nrf_gpio_pin_read(sda->number) || !nrf_gpio_pin_read(scl->number)) {
|
||||
reset_pin_number(sda->number);
|
||||
reset_pin_number(scl->number);
|
||||
mp_raise_RuntimeError(translate("SDA or SCL needs a pull up"));
|
||||
mp_raise_RuntimeError(translate("No pull up found on SDA or SCL; check your wiring"));
|
||||
}
|
||||
#endif
|
||||
|
||||
|
@ -90,7 +90,7 @@ void common_hal_busio_i2c_construct(busio_i2c_obj_t *self,
|
||||
if (!gpio_get(sda->number) || !gpio_get(scl->number)) {
|
||||
reset_pin_number(sda->number);
|
||||
reset_pin_number(scl->number);
|
||||
mp_raise_RuntimeError(translate("SDA or SCL needs a pull up"));
|
||||
mp_raise_RuntimeError(translate("No pull up found on SDA or SCL; check your wiring"));
|
||||
}
|
||||
#endif
|
||||
|
||||
|
Loading…
Reference in New Issue
Block a user