cc3200: Add GPIO25 to the pins list of the WiPy and the WiPy-SD.

This allows to properly initialize the system led and add it
to the sleep module so that it can be restored when resuming
from suspended mode.

cc3200/boards/LAUNCHXL/mpconfigboard.h

@@ -41,6 +41,7 @@
 #define MICROPY_SAFE_BOOT_PRCM                      PRCM_GPIOA2
 #define MICROPY_SYS_LED_PORT                        GPIOA1_BASE
 #define MICROPY_SAFE_BOOT_PORT                      GPIOA2_BASE
+#define MICROPY_SYS_LED_GPIO                        pin_GPIO9
 #define MICROPY_SYS_LED_PIN_NUM                     PIN_64      // GPIO9
 #define MICROPY_SAFE_BOOT_PIN_NUM                   PIN_15      // GPIO22
 #define MICROPY_SYS_LED_PORT_PIN                    GPIO_PIN_1

cc3200/boards/WIPY-SD/mpconfigboard.h

@@ -41,9 +41,10 @@
 #define MICROPY_SAFE_BOOT_PRCM                      PRCM_GPIOA3
 #define MICROPY_SYS_LED_PORT                        GPIOA3_BASE
 #define MICROPY_SAFE_BOOT_PORT                      GPIOA3_BASE
-#define MICROPY_SYS_LED_PIN_NUM                     PIN_21
+#define MICROPY_SYS_LED_GPIO                        pin_GPIO25
-#define MICROPY_SAFE_BOOT_PIN_NUM                   PIN_18
+#define MICROPY_SYS_LED_PIN_NUM                     PIN_21      // GPIO25   (SOP2)
-#define MICROPY_SYS_LED_PORT_PIN                    GPIO_PIN_1      // GPIO25   (SOP2)
+#define MICROPY_SAFE_BOOT_PIN_NUM                   PIN_18      // GPIO28
-#define MICROPY_SAFE_BOOT_PORT_PIN                  GPIO_PIN_4      // GPIO28
+#define MICROPY_SYS_LED_PORT_PIN                    GPIO_PIN_1
+#define MICROPY_SAFE_BOOT_PORT_PIN                  GPIO_PIN_4
 
 #define MICROPY_PORT_SFLASH_BLOCK_COUNT             96

cc3200/boards/WIPY-SD/pins.csv

@@ -22,3 +22,4 @@ R11,GPIO3
 R12,GPIO0
 R13,GPIO4
 R14,GPIO5
+HBL,GPIO25

cc3200/boards/WIPY/mpconfigboard.h

@@ -41,9 +41,10 @@
 #define MICROPY_SAFE_BOOT_PRCM                      PRCM_GPIOA3
 #define MICROPY_SYS_LED_PORT                        GPIOA3_BASE
 #define MICROPY_SAFE_BOOT_PORT                      GPIOA3_BASE
-#define MICROPY_SYS_LED_PIN_NUM                     PIN_21
+#define MICROPY_SYS_LED_GPIO                        pin_GPIO25
-#define MICROPY_SAFE_BOOT_PIN_NUM                   PIN_18
+#define MICROPY_SYS_LED_PIN_NUM                     PIN_21      // GPIO25   (SOP2)
-#define MICROPY_SYS_LED_PORT_PIN                    GPIO_PIN_1      // GPIO25   (SOP2)
+#define MICROPY_SAFE_BOOT_PIN_NUM                   PIN_18      // GPIO28
-#define MICROPY_SAFE_BOOT_PORT_PIN                  GPIO_PIN_4      // GPIO28
+#define MICROPY_SYS_LED_PORT_PIN                    GPIO_PIN_1
+#define MICROPY_SAFE_BOOT_PORT_PIN                  GPIO_PIN_4
 
 #define MICROPY_PORT_SFLASH_BLOCK_COUNT             96

cc3200/boards/WIPY/pins.csv

@@ -22,3 +22,4 @@ R11,GPIO3
 R12,GPIO0
 R13,GPIO4
 R14,GPIO5
+HBL,GPIO25

cc3200/misc/mperror.c

@@ -40,6 +40,10 @@
 #include "hw_common_reg.h"
 #include "pin.h"
 #include "gpio.h"
+#ifndef BOOTLOADER
+#include "pybpin.h"
+#include "pins.h"
+#endif
 #include "rom.h"
 #include "rom_map.h"
 #include "prcm.h"
@@ -64,40 +68,29 @@ struct mperror_heart_beat {
     uint32_t on_time;
     bool beating;
     bool enabled;
-} mperror_heart_beat;
+} mperror_heart_beat = {.off_time = 0, .on_time = 0, .beating = false, .enabled = false};
-
-/******************************************************************************
- DEFINE PRIVATE FUNCTIONS
- ******************************************************************************/
-STATIC void mperror_heartbeat_switch_off (void) {
-    MAP_GPIOPinWrite(MICROPY_SYS_LED_PORT, MICROPY_SYS_LED_PORT_PIN, 0);
-}
 
 /******************************************************************************
  DEFINE PUBLIC FUNCTIONS
  ******************************************************************************/
 void mperror_init0 (void) {
-    // Enable SYS GPIOs peripheral clocks
+#ifdef BOOTLOADER
+    // enable the system led and the safe boot pin peripheral clocks
     MAP_PRCMPeripheralClkEnable(MICROPY_SYS_LED_PRCM, PRCM_RUN_MODE_CLK | PRCM_SLP_MODE_CLK);
-#ifdef BOOTLOADER
     MAP_PRCMPeripheralClkEnable(MICROPY_SAFE_BOOT_PRCM, PRCM_RUN_MODE_CLK | PRCM_SLP_MODE_CLK);
-#endif
+    // configure the safe boot pin
-
-    // Configure the bld
-    MAP_PinTypeGPIO(MICROPY_SYS_LED_PIN_NUM, PIN_MODE_0, false);
-    MAP_PinConfigSet(MICROPY_SYS_LED_PIN_NUM, PIN_STRENGTH_6MA, PIN_TYPE_STD);
-    MAP_GPIODirModeSet(MICROPY_SYS_LED_PORT, MICROPY_SYS_LED_PORT_PIN, GPIO_DIR_MODE_OUT);
-
-#ifdef BOOTLOADER
-    // Configure the safe boot pin
     MAP_PinTypeGPIO(MICROPY_SAFE_BOOT_PIN_NUM, PIN_MODE_0, false);
     MAP_PinConfigSet(MICROPY_SAFE_BOOT_PIN_NUM, PIN_STRENGTH_4MA, PIN_TYPE_STD_PD);
     MAP_GPIODirModeSet(MICROPY_SAFE_BOOT_PORT, MICROPY_SAFE_BOOT_PORT_PIN, GPIO_DIR_MODE_IN);
+    // configure the bld
+    MAP_PinTypeGPIO(MICROPY_SYS_LED_PIN_NUM, PIN_MODE_0, false);
+    MAP_PinConfigSet(MICROPY_SYS_LED_PIN_NUM, PIN_STRENGTH_6MA, PIN_TYPE_STD);
+    MAP_GPIODirModeSet(MICROPY_SYS_LED_PORT, MICROPY_SYS_LED_PORT_PIN, GPIO_DIR_MODE_OUT);
+#else
+    // configure the system led
+    pin_config ((pin_obj_t *)&MICROPY_SYS_LED_GPIO, PIN_MODE_0, GPIO_DIR_MODE_OUT, PIN_TYPE_STD, PIN_STRENGTH_6MA);
 #endif
-
+    mperror_heartbeat_switch_off();
-    mperror_heart_beat.on_time = 0;
-    mperror_heart_beat.off_time = 0;
-    mperror_heart_beat.beating = false;
 }
 
 void mperror_bootloader_check_reset_cause (void) {
@@ -114,7 +107,7 @@ void mperror_bootloader_check_reset_cause (void) {
         HWREG(0x4402F024) &= 0xF7FFFFFF;
 
         // since the reset cause will be changed, we must store the right reason
-        // so that the application knows we booting the next time
+        // so that the application knows it when booting for the next time
         PRCMSignalWDTReset();
 
         MAP_PRCMHibernateWakeupSourceEnable(PRCM_HIB_SLOW_CLK_CTR);
@@ -142,6 +135,12 @@ void mperror_enable_heartbeat (void) {
     mperror_heart_beat.enabled = true;
 }
 
+void mperror_heartbeat_switch_off (void) {
+    mperror_heart_beat.on_time = 0;
+    mperror_heart_beat.off_time = 0;
+    MAP_GPIOPinWrite(MICROPY_SYS_LED_PORT, MICROPY_SYS_LED_PORT_PIN, 0);
+}
+
 void mperror_disable_heartbeat (void) {
     mperror_heart_beat.enabled = false;
     mperror_heartbeat_switch_off();
@@ -157,7 +156,7 @@ void mperror_heartbeat_signal (void) {
         }
         else {
             if ((mperror_heart_beat.off_time = HAL_GetTick()) - mperror_heart_beat.on_time > MPERROR_HEARTBEAT_ON_MS) {
-                mperror_heartbeat_switch_off();
+                MAP_GPIOPinWrite(MICROPY_SYS_LED_PORT, MICROPY_SYS_LED_PORT_PIN, 0);
                 mperror_heart_beat.beating = false;
             }
         }

cc3200/misc/mperror.h

@@ -39,6 +39,7 @@ void mperror_bootloader_check_reset_cause (void);
 void mperror_deinit_sfe_pin (void);
 void mperror_signal_error (void);
 void mperror_enable_heartbeat (void);
+void mperror_heartbeat_switch_off (void);
 void mperror_disable_heartbeat (void);
 void mperror_heartbeat_signal (void);
 

cc3200/mods/pybsleep.c

@@ -325,6 +325,9 @@ STATIC NORETURN void pybsleep_suspend_enter (void) {
     // park the gpio pins
     pybsleep_iopark();
 
+    // turn-off the heartbeat led
+    mperror_heartbeat_switch_off();
+
     // store the cpu registers
     sleep_store();
 
@@ -384,9 +387,6 @@ void pybsleep_suspend_exit (void) {
     // reinitialize simplelink's bus
     sl_IfOpen (NULL, 0);
 
-    // initialize the system led
-    mperror_init0();
-
     // restore the configuration of all active peripherals
     pybsleep_obj_wakeup();
 
@@ -610,6 +610,7 @@ STATIC mp_obj_t pyb_sleep_hibernate (mp_obj_t self_in) {
         }
     }
     wlan_stop(SL_STOP_TIMEOUT);
+    mperror_heartbeat_switch_off();
     pybsleep_flash_powerdown();
     MAP_PRCMHibernateEnter();
     return mp_const_none;

cc3200/mptask.c

@@ -118,10 +118,10 @@ soft_reset:
     mp_obj_list_append(mp_sys_path, MP_OBJ_NEW_QSTR(MP_QSTR_)); // current dir (or base dir of the script)
 
     // execute all basic initializations
-    mperror_init0();
     mpexception_init0();
     mpcallback_init0();
     pybsleep_init0();
+    mperror_init0();
     uart_init0();
     pin_init0();
     readline_init0();