From 09d207785c77c85c957471b064ceebe0d2ee0a23 Mon Sep 17 00:00:00 2001 From: Damien George Date: Sun, 30 Mar 2014 12:30:35 +0100 Subject: [PATCH] stmhal: Unify naming of HW config; make SD detect configurable. All board config macros now begin with MICROPY_HW_. Renamed PYBv10 to PYBV10, since macros should be all uppercase. Made SDCARD_DETECT configurable in mpconfigport.h, so that the SD detect pin can be easily configured. --- stmhal/Makefile | 2 +- stmhal/boards/NETDUINO_PLUS_2/mpconfigboard.h | 27 +- stmhal/boards/PYBOARD3/mpconfigboard.h | 32 -- stmhal/boards/PYBOARD4/mpconfigboard.h | 33 -- stmhal/boards/PYBV10/mpconfigboard.h | 35 ++ stmhal/boards/{PYBv10 => PYBV10}/pins.csv | 1 + .../{PYBOARD4 => PYBV10}/stm32f4xx_hal_conf.h | 0 stmhal/boards/PYBV3/mpconfigboard.h | 35 ++ stmhal/boards/{PYBOARD3 => PYBV3}/pins.csv | 2 +- .../{PYBv10 => PYBV3}/stm32f4xx_hal_conf.h | 0 stmhal/boards/PYBV4/mpconfigboard.h | 35 ++ stmhal/boards/{PYBOARD4 => PYBV4}/pins.csv | 1 + stmhal/boards/PYBV4/stm32f4xx_hal_conf.h | 393 ++++++++++++++++++ stmhal/boards/PYBv10/mpconfigboard.h | 33 -- stmhal/boards/STM32F4DISC/mpconfigboard.h | 27 +- stmhal/diskio.c | 10 + stmhal/lcd.c | 4 +- stmhal/led.c | 36 +- stmhal/pin_map.c | 2 +- stmhal/sdcard.c | 20 +- stmhal/usart.c | 2 +- stmhal/usb.c | 4 + stmhal/usbd_msc_storage.c | 6 +- stmhal/usrsw.c | 16 +- 24 files changed, 585 insertions(+), 171 deletions(-) delete mode 100644 stmhal/boards/PYBOARD3/mpconfigboard.h delete mode 100644 stmhal/boards/PYBOARD4/mpconfigboard.h create mode 100644 stmhal/boards/PYBV10/mpconfigboard.h rename stmhal/boards/{PYBv10 => PYBV10}/pins.csv (98%) rename stmhal/boards/{PYBOARD4 => PYBV10}/stm32f4xx_hal_conf.h (100%) create mode 100644 stmhal/boards/PYBV3/mpconfigboard.h rename stmhal/boards/{PYBOARD3 => PYBV3}/pins.csv (97%) rename stmhal/boards/{PYBv10 => PYBV3}/stm32f4xx_hal_conf.h (100%) create mode 100644 stmhal/boards/PYBV4/mpconfigboard.h rename stmhal/boards/{PYBOARD4 => PYBV4}/pins.csv (98%) create mode 100644 stmhal/boards/PYBV4/stm32f4xx_hal_conf.h delete mode 100644 stmhal/boards/PYBv10/mpconfigboard.h diff --git a/stmhal/Makefile b/stmhal/Makefile index 67c1ebcb42..0f3fe46cfa 100644 --- a/stmhal/Makefile +++ b/stmhal/Makefile @@ -29,7 +29,7 @@ INC += -I$(FATFS_DIR)/src CFLAGS_CORTEX_M4 = -mthumb -mtune=cortex-m4 -mabi=aapcs-linux -mcpu=cortex-m4 -mfpu=fpv4-sp-d16 -mfloat-abi=hard -fsingle-precision-constant -Wdouble-promotion CFLAGS = $(INC) -Wall -Werror -ansi -std=gnu99 $(CFLAGS_CORTEX_M4) $(COPT) -BOARD ?= PYBv10 +BOARD ?= PYBV10 ifeq ($(wildcard boards/$(BOARD)/.),) $(error Invalid BOARD specified) endif diff --git a/stmhal/boards/NETDUINO_PLUS_2/mpconfigboard.h b/stmhal/boards/NETDUINO_PLUS_2/mpconfigboard.h index 948b886819..a01d37aea8 100644 --- a/stmhal/boards/NETDUINO_PLUS_2/mpconfigboard.h +++ b/stmhal/boards/NETDUINO_PLUS_2/mpconfigboard.h @@ -19,19 +19,16 @@ #define MICROPY_HW_ENABLE_DAC (0) // USRSW is pulled low. Pressing the button makes the input go high. -#define USRSW_PIN (pin_B11) -#define USRSW_PULL (GPIO_NOPULL) -#define USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) -#define USRSW_PRESSED (1) - -/* LED */ -#define PYB_LED1 (pin_A10) // Blue LED -#define PYB_LED2 (pin_C13) // White LED (aka Power) -#define PYB_LED3 (pin_A10) // Same as Led(1) -#define PYB_LED4 (pin_C13) // Same as Led(2) - -#define PYB_OTYPE (GPIO_MODE_OUTPUT_PP) - -#define PYB_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask) -#define PYB_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask) +#define MICROPY_HW_USRSW_PIN (pin_B11) +#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) +#define MICROPY_HW_USRSW_PRESSED (1) +// LEDs +#define MICROPY_HW_LED1 (pin_A10) // Blue LED +#define MICROPY_HW_LED2 (pin_C13) // White LED (aka Power) +#define MICROPY_HW_LED3 (pin_A10) // Same as Led(1) +#define MICROPY_HW_LED4 (pin_C13) // Same as Led(2) +#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP) +#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask) +#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask) diff --git a/stmhal/boards/PYBOARD3/mpconfigboard.h b/stmhal/boards/PYBOARD3/mpconfigboard.h deleted file mode 100644 index 1cd1d94818..0000000000 --- a/stmhal/boards/PYBOARD3/mpconfigboard.h +++ /dev/null @@ -1,32 +0,0 @@ -#define PYBOARD3 - -#define MICROPY_HW_BOARD_NAME "PYBv3" - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_SDCARD (1) -#define MICROPY_HW_HAS_MMA7660 (1) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (0) -#define MICROPY_HW_HAS_WLAN (0) -#define MICROPY_HW_ENABLE_RNG (1) -#define MICROPY_HW_ENABLE_RTC (1) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (1) -#define MICROPY_HW_ENABLE_DAC (0) - -// USRSW has no pullup or pulldown, and pressing the switch makes the input go low -#define USRSW_PIN (pin_A13) -#define USRSW_PULL (GPIO_PULLUP) -#define USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) -#define USRSW_PRESSED (0) - -/* LED */ -#define PYB_LED1 (pin_A8) // R1 - red -#define PYB_LED2 (pin_A10) // R2 - red -#define PYB_LED3 (pin_C4) // G1 - green -#define PYB_LED4 (pin_C5) // G2 - green - -#define PYB_OTYPE (GPIO_MODE_OUTPUT_PP) - -#define PYB_LED_ON(pin) (pin->gpio->BSRRH = pin->pin_mask) -#define PYB_LED_OFF(pin) (pin->gpio->BSRRL = pin->pin_mask) diff --git a/stmhal/boards/PYBOARD4/mpconfigboard.h b/stmhal/boards/PYBOARD4/mpconfigboard.h deleted file mode 100644 index 9a046ffffa..0000000000 --- a/stmhal/boards/PYBOARD4/mpconfigboard.h +++ /dev/null @@ -1,33 +0,0 @@ -#define PYBOARD4 - -#define MICROPY_HW_BOARD_NAME "PYBv4" - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_SDCARD (1) -#define MICROPY_HW_HAS_MMA7660 (1) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (1) -#define MICROPY_HW_HAS_WLAN (0) -#define MICROPY_HW_ENABLE_RNG (1) -#define MICROPY_HW_ENABLE_RTC (1) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (1) -#define MICROPY_HW_ENABLE_DAC (1) - -// USRSW has no pullup or pulldown, and pressing the switch makes the input go low -#define USRSW_PIN (pin_B3) -#define USRSW_PULL (GPIO_PULLUP) -#define USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) -#define USRSW_PRESSED (0) - -/* LED */ -#define PYB_LED1 (pin_A13) // red -#define PYB_LED2 (pin_A14) // green -#define PYB_LED3 (pin_A15) // yellow -#define PYB_LED4 (pin_B4) // blue - -#define PYB_OTYPE (GPIO_MODE_OUTPUT_PP) - -#define PYB_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask) -#define PYB_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask) - diff --git a/stmhal/boards/PYBV10/mpconfigboard.h b/stmhal/boards/PYBV10/mpconfigboard.h new file mode 100644 index 0000000000..9386c04a2d --- /dev/null +++ b/stmhal/boards/PYBV10/mpconfigboard.h @@ -0,0 +1,35 @@ +#define PYBV10 + +#define MICROPY_HW_BOARD_NAME "PYBv1.0" + +#define MICROPY_HW_HAS_SWITCH (1) +#define MICROPY_HW_HAS_SDCARD (1) +#define MICROPY_HW_HAS_MMA7660 (1) +#define MICROPY_HW_HAS_LIS3DSH (0) +#define MICROPY_HW_HAS_LCD (1) +#define MICROPY_HW_HAS_WLAN (0) +#define MICROPY_HW_ENABLE_RNG (1) +#define MICROPY_HW_ENABLE_RTC (1) +#define MICROPY_HW_ENABLE_TIMER (1) +#define MICROPY_HW_ENABLE_SERVO (1) +#define MICROPY_HW_ENABLE_DAC (1) + +// USRSW has no pullup or pulldown, and pressing the switch makes the input go low +#define MICROPY_HW_USRSW_PIN (pin_B3) +#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) +#define MICROPY_HW_USRSW_PRESSED (0) + +// The pyboard has 4 LEDs +#define MICROPY_HW_LED1 (pin_A13) // red +#define MICROPY_HW_LED2 (pin_A14) // green +#define MICROPY_HW_LED3 (pin_A15) // yellow +#define MICROPY_HW_LED4 (pin_B4) // blue +#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP) +#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask) +#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask) + +// SD card detect switch +#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8) +#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP) +#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET) diff --git a/stmhal/boards/PYBv10/pins.csv b/stmhal/boards/PYBV10/pins.csv similarity index 98% rename from stmhal/boards/PYBv10/pins.csv rename to stmhal/boards/PYBV10/pins.csv index 2ca7fef184..34d96c8dd6 100644 --- a/stmhal/boards/PYBv10/pins.csv +++ b/stmhal/boards/PYBV10/pins.csv @@ -43,3 +43,4 @@ LED_RED,PA13 LED_GREEN,PA14 LED_YELLOW,PA15 SW,PB3 +SD,PA8 diff --git a/stmhal/boards/PYBOARD4/stm32f4xx_hal_conf.h b/stmhal/boards/PYBV10/stm32f4xx_hal_conf.h similarity index 100% rename from stmhal/boards/PYBOARD4/stm32f4xx_hal_conf.h rename to stmhal/boards/PYBV10/stm32f4xx_hal_conf.h diff --git a/stmhal/boards/PYBV3/mpconfigboard.h b/stmhal/boards/PYBV3/mpconfigboard.h new file mode 100644 index 0000000000..f47a01bc4c --- /dev/null +++ b/stmhal/boards/PYBV3/mpconfigboard.h @@ -0,0 +1,35 @@ +#define PYBV3 + +#define MICROPY_HW_BOARD_NAME "PYBv3" + +#define MICROPY_HW_HAS_SWITCH (1) +#define MICROPY_HW_HAS_SDCARD (1) +#define MICROPY_HW_HAS_MMA7660 (1) +#define MICROPY_HW_HAS_LIS3DSH (0) +#define MICROPY_HW_HAS_LCD (0) +#define MICROPY_HW_HAS_WLAN (0) +#define MICROPY_HW_ENABLE_RNG (1) +#define MICROPY_HW_ENABLE_RTC (1) +#define MICROPY_HW_ENABLE_TIMER (1) +#define MICROPY_HW_ENABLE_SERVO (1) +#define MICROPY_HW_ENABLE_DAC (0) + +// USRSW has no pullup or pulldown, and pressing the switch makes the input go low +#define MICROPY_HW_USRSW_PIN (pin_A13) +#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) +#define MICROPY_HW_USRSW_PRESSED (0) + +// LEDs +#define MICROPY_HW_LED1 (pin_A8) // R1 - red +#define MICROPY_HW_LED2 (pin_A10) // R2 - red +#define MICROPY_HW_LED3 (pin_C4) // G1 - green +#define MICROPY_HW_LED4 (pin_C5) // G2 - green +#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP) +#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRH = pin->pin_mask) +#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRL = pin->pin_mask) + +// SD card detect switch +#define MICROPY_HW_SDCARD_DETECT_PIN (pin_C13) +#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLDOWN) +#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_SET) diff --git a/stmhal/boards/PYBOARD3/pins.csv b/stmhal/boards/PYBV3/pins.csv similarity index 97% rename from stmhal/boards/PYBOARD3/pins.csv rename to stmhal/boards/PYBV3/pins.csv index cc07b15445..cce8a9e111 100644 --- a/stmhal/boards/PYBOARD3/pins.csv +++ b/stmhal/boards/PYBV3/pins.csv @@ -34,4 +34,4 @@ LED_R2,PA10 LED_G1,PC4 LED_G2,PC5 SW,PA13 - +SD,PC13 diff --git a/stmhal/boards/PYBv10/stm32f4xx_hal_conf.h b/stmhal/boards/PYBV3/stm32f4xx_hal_conf.h similarity index 100% rename from stmhal/boards/PYBv10/stm32f4xx_hal_conf.h rename to stmhal/boards/PYBV3/stm32f4xx_hal_conf.h diff --git a/stmhal/boards/PYBV4/mpconfigboard.h b/stmhal/boards/PYBV4/mpconfigboard.h new file mode 100644 index 0000000000..1846491c3a --- /dev/null +++ b/stmhal/boards/PYBV4/mpconfigboard.h @@ -0,0 +1,35 @@ +#define PYBV4 + +#define MICROPY_HW_BOARD_NAME "PYBv4" + +#define MICROPY_HW_HAS_SWITCH (1) +#define MICROPY_HW_HAS_SDCARD (1) +#define MICROPY_HW_HAS_MMA7660 (1) +#define MICROPY_HW_HAS_LIS3DSH (0) +#define MICROPY_HW_HAS_LCD (1) +#define MICROPY_HW_HAS_WLAN (0) +#define MICROPY_HW_ENABLE_RNG (1) +#define MICROPY_HW_ENABLE_RTC (1) +#define MICROPY_HW_ENABLE_TIMER (1) +#define MICROPY_HW_ENABLE_SERVO (1) +#define MICROPY_HW_ENABLE_DAC (1) + +// USRSW has no pullup or pulldown, and pressing the switch makes the input go low +#define MICROPY_HW_USRSW_PIN (pin_B3) +#define MICROPY_HW_USRSW_PULL (GPIO_PULLUP) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) +#define MICROPY_HW_USRSW_PRESSED (0) + +// LEDs +#define MICROPY_HW_LED1 (pin_A13) // red +#define MICROPY_HW_LED2 (pin_A14) // green +#define MICROPY_HW_LED3 (pin_A15) // yellow +#define MICROPY_HW_LED4 (pin_B4) // blue +#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP) +#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask) +#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask) + +// SD card detect switch +#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8) +#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP) +#define MICROPY_HW_SDCARD_DETECT_PRESENT (GPIO_PIN_RESET) diff --git a/stmhal/boards/PYBOARD4/pins.csv b/stmhal/boards/PYBV4/pins.csv similarity index 98% rename from stmhal/boards/PYBOARD4/pins.csv rename to stmhal/boards/PYBV4/pins.csv index 2ca7fef184..34d96c8dd6 100644 --- a/stmhal/boards/PYBOARD4/pins.csv +++ b/stmhal/boards/PYBV4/pins.csv @@ -43,3 +43,4 @@ LED_RED,PA13 LED_GREEN,PA14 LED_YELLOW,PA15 SW,PB3 +SD,PA8 diff --git a/stmhal/boards/PYBV4/stm32f4xx_hal_conf.h b/stmhal/boards/PYBV4/stm32f4xx_hal_conf.h new file mode 100644 index 0000000000..315c24dc67 --- /dev/null +++ b/stmhal/boards/PYBV4/stm32f4xx_hal_conf.h @@ -0,0 +1,393 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_conf.h + * @author MCD Application Team + * @version V1.0.1 + * @date 26-February-2014 + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© COPYRIGHT(c) 2014 STMicroelectronics

+ * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_HAL_CONF_H +#define __STM32F4xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +#define STM32F405xx +#define USE_USB_FS + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +#define HAL_CAN_MODULE_ENABLED +#define HAL_CRC_MODULE_ENABLED +#define HAL_CRYP_MODULE_ENABLED +#define HAL_DAC_MODULE_ENABLED +#define HAL_DCMI_MODULE_ENABLED +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_DMA2D_MODULE_ENABLED */ +#define HAL_ETH_MODULE_ENABLED +#define HAL_FLASH_MODULE_ENABLED +#define HAL_NAND_MODULE_ENABLED +#define HAL_NOR_MODULE_ENABLED +#define HAL_PCCARD_MODULE_ENABLED +#define HAL_SRAM_MODULE_ENABLED +/* #define HAL_SDRAM_MODULE_ENABLED */ +#define HAL_HASH_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +#define HAL_I2C_MODULE_ENABLED +#define HAL_I2S_MODULE_ENABLED +#define HAL_IWDG_MODULE_ENABLED +#define HAL_LTDC_MODULE_ENABLED +#define HAL_PWR_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED +#define HAL_RNG_MODULE_ENABLED +#define HAL_RTC_MODULE_ENABLED +/* #define HAL_SAI_MODULE_ENABLED */ +#define HAL_SD_MODULE_ENABLED +#define HAL_SPI_MODULE_ENABLED +#define HAL_TIM_MODULE_ENABLED +#define HAL_UART_MODULE_ENABLED +#define HAL_USART_MODULE_ENABLED +#define HAL_IRDA_MODULE_ENABLED +#define HAL_SMARTCARD_MODULE_ENABLED +#define HAL_WWDG_MODULE_ENABLED +#define HAL_CORTEX_MODULE_ENABLED +#define HAL_PCD_MODULE_ENABLED +#define HAL_HCD_MODULE_ENABLED + + +/* ########################## HSE/HSI Values adaptation ##################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#if !defined (EXTERNAL_CLOCK_VALUE) + #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ +#define USE_RTOS 0 +#define PREFETCH_ENABLE 1 +#define INSTRUCTION_CACHE_ENABLE 1 +#define DATA_CACHE_ENABLE 1 + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1 */ + +/* ################## Ethernet peripheral configuration ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2 +#define MAC_ADDR1 0 +#define MAC_ADDR2 0 +#define MAC_ADDR3 0 +#define MAC_ADDR4 0 +#define MAC_ADDR5 0 + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ + +/* DP83848 PHY Address*/ +#define DP83848_PHY_ADDRESS 0x01 +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY ((uint32_t)0x000000FF) +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) + +#define PHY_READ_TO ((uint32_t)0x0000FFFF) +#define PHY_WRITE_TO ((uint32_t)0x0000FFFF) + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ + +#define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */ +#define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */ +#define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */ + +#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ +#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ + +#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ +#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ + +#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ +#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32f4xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32f4xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32f4xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32f4xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32f4xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32f4xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32f4xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32f4xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32f4xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32f4xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32f4xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED + #include "stm32f4xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32f4xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32f4xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32f4xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32f4xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_PCCARD_MODULE_ENABLED + #include "stm32f4xx_hal_pccard.h" +#endif /* HAL_PCCARD_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32f4xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32f4xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32f4xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32f4xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32f4xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED + #include "stm32f4xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32f4xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32f4xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32f4xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32f4xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32f4xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32f4xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32f4xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32f4xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32f4xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32f4xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32f4xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32f4xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32f4xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32f4xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0) +#endif /* USE_FULL_ASSERT */ + + + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F4xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/stmhal/boards/PYBv10/mpconfigboard.h b/stmhal/boards/PYBv10/mpconfigboard.h deleted file mode 100644 index f5ebe25cc4..0000000000 --- a/stmhal/boards/PYBv10/mpconfigboard.h +++ /dev/null @@ -1,33 +0,0 @@ -#define PYBv10 - -#define MICROPY_HW_BOARD_NAME "PYBv1.0" - -#define MICROPY_HW_HAS_SWITCH (1) -#define MICROPY_HW_HAS_SDCARD (1) -#define MICROPY_HW_HAS_MMA7660 (1) -#define MICROPY_HW_HAS_LIS3DSH (0) -#define MICROPY_HW_HAS_LCD (1) -#define MICROPY_HW_HAS_WLAN (0) -#define MICROPY_HW_ENABLE_RNG (1) -#define MICROPY_HW_ENABLE_RTC (1) -#define MICROPY_HW_ENABLE_TIMER (1) -#define MICROPY_HW_ENABLE_SERVO (1) -#define MICROPY_HW_ENABLE_DAC (1) - -// USRSW has no pullup or pulldown, and pressing the switch makes the input go low -#define USRSW_PIN (pin_B3) -#define USRSW_PULL (GPIO_PULLUP) -#define USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING) -#define USRSW_PRESSED (0) - -/* LED */ -#define PYB_LED1 (pin_A13) // red -#define PYB_LED2 (pin_A14) // green -#define PYB_LED3 (pin_A15) // yellow -#define PYB_LED4 (pin_B4) // blue - -#define PYB_OTYPE (GPIO_MODE_OUTPUT_PP) - -#define PYB_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask) -#define PYB_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask) - diff --git a/stmhal/boards/STM32F4DISC/mpconfigboard.h b/stmhal/boards/STM32F4DISC/mpconfigboard.h index 2a58b27bdf..3bfdfbfb80 100644 --- a/stmhal/boards/STM32F4DISC/mpconfigboard.h +++ b/stmhal/boards/STM32F4DISC/mpconfigboard.h @@ -15,19 +15,16 @@ #define MICROPY_HW_ENABLE_DAC (0) // USRSW is pulled low. Pressing the button makes the input go high. -#define USRSW_PIN (pin_A0) -#define USRSW_PULL (GPIO_NOPULL) -#define USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) -#define USRSW_PRESSED (1) - -/* LED */ -#define PYB_LED1 (pin_D14) // red -#define PYB_LED2 (pin_D12) // green -#define PYB_LED3 (pin_D13) // orange -#define PYB_LED4 (pin_D15) // blue - -#define PYB_OTYPE (GPIO_MODE_OUTPUT_PP) - -#define PYB_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask) -#define PYB_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask) +#define MICROPY_HW_USRSW_PIN (pin_A0) +#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL) +#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING) +#define MICROPY_HW_USRSW_PRESSED (1) +// LEDs +#define MICROPY_HW_LED1 (pin_D14) // red +#define MICROPY_HW_LED2 (pin_D12) // green +#define MICROPY_HW_LED3 (pin_D13) // orange +#define MICROPY_HW_LED4 (pin_D15) // blue +#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP) +#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRRL = pin->pin_mask) +#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRRH = pin->pin_mask) diff --git a/stmhal/diskio.c b/stmhal/diskio.c index 4d6f998f55..0c67a23d68 100644 --- a/stmhal/diskio.c +++ b/stmhal/diskio.c @@ -41,12 +41,14 @@ DSTATUS disk_initialize ( storage_init(); return 0; +#if MICROPY_HW_HAS_SDCARD case PD_SDCARD: if (!sdcard_power_on()) { return STA_NODISK; } // TODO return STA_PROTECT if SD card is read only return 0; +#endif } return STA_NOINIT; @@ -65,9 +67,11 @@ DSTATUS disk_status ( // flash is ready return 0; +#if MICROPY_HW_HAS_SDCARD case PD_SDCARD: // TODO return STA_PROTECT if SD card is read only return 0; +#endif } return STA_NOINIT; @@ -93,11 +97,13 @@ DRESULT disk_read ( } return RES_OK; +#if MICROPY_HW_HAS_SDCARD case PD_SDCARD: if (!sdcard_read_blocks(buff, sector, count)) { return RES_ERROR; } return RES_OK; +#endif } return RES_PARERR; @@ -124,11 +130,13 @@ DRESULT disk_write ( } return RES_OK; +#if MICROPY_HW_HAS_SDCARD case PD_SDCARD: if (!sdcard_write_blocks(buff, sector, count)) { return RES_ERROR; } return RES_OK; +#endif } return RES_PARERR; @@ -160,6 +168,7 @@ DRESULT disk_ioctl ( } break; +#if MICROPY_HW_HAS_SDCARD case PD_SDCARD: switch (cmd) { case CTRL_SYNC: @@ -170,6 +179,7 @@ DRESULT disk_ioctl ( return RES_OK; } break; +#endif } return RES_PARERR; diff --git a/stmhal/lcd.c b/stmhal/lcd.c index c5952fa48c..e2b9e22976 100644 --- a/stmhal/lcd.c +++ b/stmhal/lcd.c @@ -17,14 +17,14 @@ #include "font_petme128_8x8.h" #include "lcd.h" -#if defined(PYBOARD3) +#if defined(PYBV3) #define PYB_LCD_PORT (GPIOA) #define PYB_LCD_CS1_PIN (GPIO_PIN_0) #define PYB_LCD_RST_PIN (GPIO_PIN_1) #define PYB_LCD_A0_PIN (GPIO_PIN_2) #define PYB_LCD_SCL_PIN (GPIO_PIN_3) #define PYB_LCD_SI_PIN (GPIO_PIN_4) -#elif defined(PYBOARD4) || defined(PYBv10) +#elif defined(PYBV4) || defined(PYBV10) // X position #define PYB_LCD_PORT (GPIOA) #define PYB_LCD_CS1_PIN (GPIO_PIN_2) // X3 diff --git a/stmhal/led.c b/stmhal/led.c index 5ff50fbb88..506e82e548 100644 --- a/stmhal/led.c +++ b/stmhal/led.c @@ -15,13 +15,13 @@ #include "build/pins.h" static const pin_obj_t *gLed[] = { - &PYB_LED1, -#if defined(PYB_LED2) - &PYB_LED2, -#if defined(PYB_LED3) - &PYB_LED3, -#if defined(PYB_LED4) - &PYB_LED4, + &MICROPY_HW_LED1, +#if defined(MICROPY_HW_LED2) + &MICROPY_HW_LED2, +#if defined(MICROPY_HW_LED3) + &MICROPY_HW_LED3, +#if defined(MICROPY_HW_LED4) + &MICROPY_HW_LED4, #endif #endif #endif @@ -34,27 +34,27 @@ void led_init(void) { /* Configure I/O speed, mode, output type and pull */ GPIO_InitStructure.Speed = GPIO_SPEED_LOW; - GPIO_InitStructure.Mode = PYB_OTYPE; + GPIO_InitStructure.Mode = MICROPY_HW_LED_OTYPE; GPIO_InitStructure.Pull = GPIO_NOPULL; /* Turn off LEDs and initialize */ for (int led = 0; led < NUM_LEDS; led++) { - PYB_LED_OFF(gLed[led]); + MICROPY_HW_LED_OFF(gLed[led]); GPIO_InitStructure.Pin = gLed[led]->pin_mask; HAL_GPIO_Init(gLed[led]->gpio, &GPIO_InitStructure); } -#if defined(PYBOARD4) || defined(PYBv10) +#if defined(PYBV4) || defined(PYBV10) // LED4 (blue) is on PB4 which is TIM3_CH1 // we use PWM on this channel to fade the LED // GPIO configuration - GPIO_InitStructure.Pin = PYB_LED4.pin_mask; + GPIO_InitStructure.Pin = MICROPY_HW_LED4.pin_mask; GPIO_InitStructure.Mode = GPIO_MODE_AF_PP; GPIO_InitStructure.Speed = GPIO_SPEED_FAST; GPIO_InitStructure.Pull = GPIO_NOPULL; GPIO_InitStructure.Alternate = GPIO_AF2_TIM3; - HAL_GPIO_Init(PYB_LED4.gpio, &GPIO_InitStructure); + HAL_GPIO_Init(MICROPY_HW_LED4.gpio, &GPIO_InitStructure); // PWM mode configuration TIM_OC_InitTypeDef oc_init; @@ -73,7 +73,7 @@ void led_state(pyb_led_t led, int state) { if (led < 1 || led > NUM_LEDS) { return; } -#if defined(PYBOARD4) || defined(PYBv10) +#if defined(PYBV4) || defined(PYBV10) if (led == 4) { if (state) { TIM3->CCR1 = 0xffff; @@ -87,10 +87,10 @@ void led_state(pyb_led_t led, int state) { //printf("led_state(%d,%d)\n", led, state); if (state == 0) { // turn LED off - PYB_LED_OFF(led_pin); + MICROPY_HW_LED_OFF(led_pin); } else { // turn LED on - PYB_LED_ON(led_pin); + MICROPY_HW_LED_ON(led_pin); } } @@ -99,7 +99,7 @@ void led_toggle(pyb_led_t led) { return; } -#if defined(PYBOARD4) || defined(PYBv10) +#if defined(PYBV4) || defined(PYBV10) if (led == 4) { if (TIM3->CCR1 == 0) { TIM3->CCR1 = 0xffff; @@ -129,7 +129,7 @@ int led_get_intensity(pyb_led_t led) { return 0; } -#if defined(PYBOARD4) || defined(PYBv10) +#if defined(PYBV4) || defined(PYBV10) if (led == 4) { machine_uint_t i = TIM3->CCR1 * 255 / ((USBD_CDC_POLLING_INTERVAL*1000) - 1); if (i > 255) { @@ -153,7 +153,7 @@ int led_get_intensity(pyb_led_t led) { } void led_set_intensity(pyb_led_t led, machine_int_t intensity) { -#if defined(PYBOARD4) || defined(PYBv10) +#if defined(PYBV4) || defined(PYBV10) if (led == 4) { // set intensity using PWM pulse width if (intensity < 0) { diff --git a/stmhal/pin_map.c b/stmhal/pin_map.c index c546231c80..a754d24a05 100644 --- a/stmhal/pin_map.c +++ b/stmhal/pin_map.c @@ -23,7 +23,7 @@ // // CPU pins which correspond to the board pins are available // as pyb.cpu.Name. For the CPU pins, the names are the port letter -// followed by the pin number. On the PYBOARD4, pyb.Pin.board.X1 and +// followed by the pin number. On the PYBV4, pyb.Pin.board.X1 and // pyb.Pin.cpu.B6 are the same pin. // // You can also use strings: diff --git a/stmhal/sdcard.c b/stmhal/sdcard.c index 5620aef5b4..ae03c9f3fa 100644 --- a/stmhal/sdcard.c +++ b/stmhal/sdcard.c @@ -9,15 +9,13 @@ #include "map.h" #include "runtime.h" #include "sdcard.h" +#include "pin.h" +#include "build/pins.h" + +#if MICROPY_HW_HAS_SDCARD static SD_HandleTypeDef sd_handle; -#define SDCARD_DETECT_GPIO_PORT (GPIOA) -#define SDCARD_DETECT_GPIO_PIN (GPIO_PIN_8) -#define SDCARD_DETECT_GPIO_PULL (GPIO_PULLUP) -#define SDCARD_DETECT_GPIO_PRESENT (GPIO_PIN_RESET) -#define __SDCARD_DETECT_GPIO_CLK_ENABLE() __GPIOA_CLK_ENABLE() - void sdcard_init(void) { GPIO_InitTypeDef GPIO_Init_Structure; @@ -39,10 +37,10 @@ void sdcard_init(void) { // configure the SD card detect pin // we do this here so we can detect if the SD card is inserted before powering it on GPIO_Init_Structure.Mode = GPIO_MODE_INPUT; - GPIO_Init_Structure.Pull = SDCARD_DETECT_GPIO_PULL; + GPIO_Init_Structure.Pull = MICROPY_HW_SDCARD_DETECT_PULL; GPIO_Init_Structure.Speed = GPIO_SPEED_HIGH; - GPIO_Init_Structure.Pin = SDCARD_DETECT_GPIO_PIN; - HAL_GPIO_Init(SDCARD_DETECT_GPIO_PORT, &GPIO_Init_Structure); + GPIO_Init_Structure.Pin = MICROPY_HW_SDCARD_DETECT_PIN.pin_mask; + HAL_GPIO_Init(MICROPY_HW_SDCARD_DETECT_PIN.gpio, &GPIO_Init_Structure); } void HAL_SD_MspInit(SD_HandleTypeDef *hsd) { @@ -60,7 +58,7 @@ void HAL_SD_MspDeInit(SD_HandleTypeDef *hsd) { } bool sdcard_is_present(void) { - return HAL_GPIO_ReadPin(SDCARD_DETECT_GPIO_PORT, SDCARD_DETECT_GPIO_PIN) == SDCARD_DETECT_GPIO_PRESENT; + return HAL_GPIO_ReadPin(MICROPY_HW_SDCARD_DETECT_PIN.gpio, MICROPY_HW_SDCARD_DETECT_PIN.pin_mask) == MICROPY_HW_SDCARD_DETECT_PRESENT; } bool sdcard_power_on(void) { @@ -248,3 +246,5 @@ static const mp_obj_type_t sdcard_type = { }; const mp_obj_base_t pyb_sdcard_obj = {&sdcard_type}; + +#endif // MICROPY_HW_HAS_SDCARD diff --git a/stmhal/usart.c b/stmhal/usart.c index daf8a9e1fc..14539c597c 100644 --- a/stmhal/usart.c +++ b/stmhal/usart.c @@ -52,7 +52,7 @@ void usart_init(pyb_usart_obj_t *usart_obj, uint32_t baudrate) { case PYB_USART_3: USARTx = USART3; -#if defined(PYBOARD3) || defined(PYBOARD4) +#if defined(PYBV3) || defined(PYBV4) GPIO_Port = GPIOB; GPIO_AF_USARTx = GPIO_AF7_USART3; GPIO_Pin = GPIO_PIN_10 | GPIO_PIN_11; diff --git a/stmhal/usb.c b/stmhal/usb.c index 3d795f1823..97ea2e1b41 100644 --- a/stmhal/usb.c +++ b/stmhal/usb.c @@ -31,11 +31,15 @@ void pyb_usb_dev_init(usb_device_mode_t mode, usb_storage_medium_t medium) { USBD_Init(&hUSBDDevice, &VCP_Desc, 0); USBD_RegisterClass(&hUSBDDevice, &USBD_CDC_MSC_HID); USBD_CDC_RegisterInterface(&hUSBDDevice, (USBD_CDC_ItfTypeDef*)&USBD_CDC_fops); +#if MICROPY_HW_HAS_SDCARD if (medium == USB_STORAGE_MEDIUM_FLASH) { USBD_MSC_RegisterStorage(&hUSBDDevice, (USBD_StorageTypeDef*)&USBD_FLASH_STORAGE_fops); } else { USBD_MSC_RegisterStorage(&hUSBDDevice, (USBD_StorageTypeDef*)&USBD_SDCARD_STORAGE_fops); } +#else + USBD_MSC_RegisterStorage(&hUSBDDevice, (USBD_StorageTypeDef*)&USBD_FLASH_STORAGE_fops); +#endif USBD_Start(&hUSBDDevice); } dev_is_enabled = 1; diff --git a/stmhal/usbd_msc_storage.c b/stmhal/usbd_msc_storage.c index 1b4545cd30..f3ecd023d1 100644 --- a/stmhal/usbd_msc_storage.c +++ b/stmhal/usbd_msc_storage.c @@ -27,7 +27,7 @@ ****************************************************************************** */ -#include "usbd_cdc_msc.h" +#include "usbd_cdc_msc_hid.h" #include "usbd_msc_storage.h" #include "misc.h" @@ -159,6 +159,8 @@ const USBD_StorageTypeDef USBD_FLASH_STORAGE_fops = { /******************************************************************************/ // Callback functions for when the SD card is the mass storage device +#if MICROPY_HW_HAS_SDCARD + static const int8_t SDCARD_STORAGE_Inquirydata[] = { // 36 bytes // LUN 0 0x00, @@ -318,3 +320,5 @@ const USBD_StorageTypeDef USBD_SDCARD_STORAGE_fops = { SDCARD_STORAGE_GetMaxLun, (int8_t *)SDCARD_STORAGE_Inquirydata, }; + +#endif // MICROPY_HW_HAS_SDCARD diff --git a/stmhal/usrsw.c b/stmhal/usrsw.c index 60032c4ecb..038fbf9efb 100644 --- a/stmhal/usrsw.c +++ b/stmhal/usrsw.c @@ -42,26 +42,26 @@ static MP_DEFINE_CONST_FUN_OBJ_1(switch_callback_obj, switch_callback); // this function inits the switch GPIO so that it can be used void switch_init0(void) { GPIO_InitTypeDef init; - init.Pin = USRSW_PIN.pin_mask; + init.Pin = MICROPY_HW_USRSW_PIN.pin_mask; init.Mode = GPIO_MODE_INPUT; - init.Pull = USRSW_PULL; + init.Pull = MICROPY_HW_USRSW_PULL; init.Speed = GPIO_SPEED_FAST; - HAL_GPIO_Init(USRSW_PIN.gpio, &init); + HAL_GPIO_Init(MICROPY_HW_USRSW_PIN.gpio, &init); } // this function inits the callback and EXTI function of the switch void switch_init(void) { switch_user_callback_obj = mp_const_none; - exti_register((mp_obj_t)&USRSW_PIN, - MP_OBJ_NEW_SMALL_INT(USRSW_EXTI_MODE), - MP_OBJ_NEW_SMALL_INT(USRSW_PULL), + exti_register((mp_obj_t)&MICROPY_HW_USRSW_PIN, + MP_OBJ_NEW_SMALL_INT(MICROPY_HW_USRSW_EXTI_MODE), + MP_OBJ_NEW_SMALL_INT(MICROPY_HW_USRSW_PULL), (mp_obj_t)&switch_callback_obj, NULL); } int switch_get(void) { - int val = ((USRSW_PIN.gpio->IDR & USRSW_PIN.pin_mask) != 0); - return val == USRSW_PRESSED; + int val = ((MICROPY_HW_USRSW_PIN.gpio->IDR & MICROPY_HW_USRSW_PIN.pin_mask) != 0); + return val == MICROPY_HW_USRSW_PRESSED; } /******************************************************************************/