294 lines
10 KiB
C
294 lines
10 KiB
C
|
/**
|
||
|
|
******************************************************************************
|
||
|
|
* @file usb_conf.h
|
||
|
|
* @author MCD Application Team
|
||
|
|
* @version V1.1.0
|
||
|
|
* @date 19-March-2012
|
||
|
|
* @brief General low level driver configuration
|
||
|
|
******************************************************************************
|
||
|
|
* @attention
|
||
|
|
*
|
||
|
|
* <h2><center>© COPYRIGHT 2012 STMicroelectronics</center></h2>
|
||
|
|
*
|
||
|
|
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
|
||
|
|
* You may not use this file except in compliance with the License.
|
||
|
|
* You may obtain a copy of the License at:
|
||
|
|
*
|
||
|
|
* http://www.st.com/software_license_agreement_liberty_v2
|
||
|
|
*
|
||
|
|
* Unless required by applicable law or agreed to in writing, software
|
||
|
|
* distributed under the License is distributed on an "AS IS" BASIS,
|
||
|
|
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||
|
|
* See the License for the specific language governing permissions and
|
||
|
|
* limitations under the License.
|
||
|
|
*
|
||
|
|
******************************************************************************
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* Define to prevent recursive inclusion -------------------------------------*/
|
||
|
|
#ifndef __USB_CONF__H__
|
||
|
|
#define __USB_CONF__H__
|
||
|
|
|
||
|
|
/* Includes ------------------------------------------------------------------*/
|
||
|
|
#include "stm32f4xx.h"
|
||
|
|
//#include "stm324xg_eval.h"
|
||
|
|
//#include "stm324xg_eval_lcd.h"
|
||
|
|
//#include "stm324xg_eval_ioe.h"
|
||
|
|
//#include "stm324xg_eval_sdio_sd.h"
|
||
|
|
|
||
|
|
|
||
|
|
/** @addtogroup USB_OTG_DRIVER
|
||
|
|
* @{
|
||
|
|
*/
|
||
|
|
|
||
|
|
/** @defgroup USB_CONF
|
||
|
|
* @brief USB low level driver configuration file
|
||
|
|
* @{
|
||
|
|
*/
|
||
|
|
|
||
|
|
/** @defgroup USB_CONF_Exported_Defines
|
||
|
|
* @{
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* USB Core and PHY interface configuration.
|
||
|
|
Tip: To avoid modifying these defines each time you need to change the USB
|
||
|
|
configuration, you can declare the needed define in your toolchain
|
||
|
|
compiler preprocessor.
|
||
|
|
*/
|
||
|
|
/****************** USB OTG FS PHY CONFIGURATION *******************************
|
||
|
|
* The USB OTG FS Core supports one on-chip Full Speed PHY.
|
||
|
|
*
|
||
|
|
* The USE_EMBEDDED_PHY symbol is defined in the project compiler preprocessor
|
||
|
|
* when FS core is used.
|
||
|
|
*******************************************************************************/
|
||
|
|
#ifndef USE_USB_OTG_FS
|
||
|
|
#define USE_USB_OTG_FS
|
||
|
|
#endif /* USE_USB_OTG_FS */
|
||
|
|
|
||
|
|
#ifdef USE_USB_OTG_FS
|
||
|
|
#define USB_OTG_FS_CORE
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/****************** USB OTG HS PHY CONFIGURATION *******************************
|
||
|
|
* The USB OTG HS Core supports two PHY interfaces:
|
||
|
|
* (i) An ULPI interface for the external High Speed PHY: the USB HS Core will
|
||
|
|
* operate in High speed mode
|
||
|
|
* (ii) An on-chip Full Speed PHY: the USB HS Core will operate in Full speed mode
|
||
|
|
*
|
||
|
|
* You can select the PHY to be used using one of these two defines:
|
||
|
|
* (i) USE_ULPI_PHY: if the USB OTG HS Core is to be used in High speed mode
|
||
|
|
* (ii) USE_EMBEDDED_PHY: if the USB OTG HS Core is to be used in Full speed mode
|
||
|
|
*
|
||
|
|
* Notes:
|
||
|
|
* - The USE_ULPI_PHY symbol is defined in the project compiler preprocessor as
|
||
|
|
* default PHY when HS core is used.
|
||
|
|
* - On STM322xG-EVAL and STM324xG-EVAL boards, only configuration(i) is available.
|
||
|
|
* Configuration (ii) need a different hardware, for more details refer to your
|
||
|
|
* STM32 device datasheet.
|
||
|
|
*******************************************************************************/
|
||
|
|
#ifndef USE_USB_OTG_HS
|
||
|
|
//#define USE_USB_OTG_HS
|
||
|
|
#endif /* USE_USB_OTG_HS */
|
||
|
|
|
||
|
|
#ifndef USE_ULPI_PHY
|
||
|
|
//#define USE_ULPI_PHY
|
||
|
|
#endif /* USE_ULPI_PHY */
|
||
|
|
|
||
|
|
#ifndef USE_EMBEDDED_PHY
|
||
|
|
//#define USE_EMBEDDED_PHY
|
||
|
|
#endif /* USE_EMBEDDED_PHY */
|
||
|
|
|
||
|
|
#ifdef USE_USB_OTG_HS
|
||
|
|
#define USB_OTG_HS_CORE
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/*******************************************************************************
|
||
|
|
* FIFO Size Configuration in Device mode
|
||
|
|
*
|
||
|
|
* (i) Receive data FIFO size = RAM for setup packets +
|
||
|
|
* OUT endpoint control information +
|
||
|
|
* data OUT packets + miscellaneous
|
||
|
|
* Space = ONE 32-bits words
|
||
|
|
* --> RAM for setup packets = 10 spaces
|
||
|
|
* (n is the nbr of CTRL EPs the device core supports)
|
||
|
|
* --> OUT EP CTRL info = 1 space
|
||
|
|
* (one space for status information written to the FIFO along with each
|
||
|
|
* received packet)
|
||
|
|
* --> data OUT packets = (Largest Packet Size / 4) + 1 spaces
|
||
|
|
* (MINIMUM to receive packets)
|
||
|
|
* --> OR data OUT packets = at least 2*(Largest Packet Size / 4) + 1 spaces
|
||
|
|
* (if high-bandwidth EP is enabled or multiple isochronous EPs)
|
||
|
|
* --> miscellaneous = 1 space per OUT EP
|
||
|
|
* (one space for transfer complete status information also pushed to the
|
||
|
|
* FIFO with each endpoint's last packet)
|
||
|
|
*
|
||
|
|
* (ii)MINIMUM RAM space required for each IN EP Tx FIFO = MAX packet size for
|
||
|
|
* that particular IN EP. More space allocated in the IN EP Tx FIFO results
|
||
|
|
* in a better performance on the USB and can hide latencies on the AHB.
|
||
|
|
*
|
||
|
|
* (iii) TXn min size = 16 words. (n : Transmit FIFO index)
|
||
|
|
* (iv) When a TxFIFO is not used, the Configuration should be as follows:
|
||
|
|
* case 1 : n > m and Txn is not used (n,m : Transmit FIFO indexes)
|
||
|
|
* --> Txm can use the space allocated for Txn.
|
||
|
|
* case2 : n < m and Txn is not used (n,m : Transmit FIFO indexes)
|
||
|
|
* --> Txn should be configured with the minimum space of 16 words
|
||
|
|
* (v) The FIFO is used optimally when used TxFIFOs are allocated in the top
|
||
|
|
* of the FIFO.Ex: use EP1 and EP2 as IN instead of EP1 and EP3 as IN ones.
|
||
|
|
* (vi) In HS case 12 FIFO locations should be reserved for internal DMA registers
|
||
|
|
* so total FIFO size should be 1012 Only instead of 1024
|
||
|
|
*******************************************************************************/
|
||
|
|
|
||
|
|
/****************** USB OTG HS CONFIGURATION **********************************/
|
||
|
|
#ifdef USB_OTG_HS_CORE
|
||
|
|
#define RX_FIFO_HS_SIZE 512
|
||
|
|
#define TX0_FIFO_HS_SIZE 128
|
||
|
|
#define TX1_FIFO_HS_SIZE 372
|
||
|
|
#define TX2_FIFO_HS_SIZE 64
|
||
|
|
#define TX3_FIFO_HS_SIZE 0
|
||
|
|
#define TX4_FIFO_HS_SIZE 0
|
||
|
|
#define TX5_FIFO_HS_SIZE 0
|
||
|
|
|
||
|
|
// #define USB_OTG_HS_SOF_OUTPUT_ENABLED
|
||
|
|
|
||
|
|
#ifdef USE_ULPI_PHY
|
||
|
|
#define USB_OTG_ULPI_PHY_ENABLED
|
||
|
|
#endif
|
||
|
|
#ifdef USE_EMBEDDED_PHY
|
||
|
|
#define USB_OTG_EMBEDDED_PHY_ENABLED
|
||
|
|
/* wakeup is working only when HS core is configured in FS mode */
|
||
|
|
#define USB_OTG_HS_LOW_PWR_MGMT_SUPPORT
|
||
|
|
#endif
|
||
|
|
/* #define USB_OTG_HS_INTERNAL_DMA_ENABLED */ /* Be aware that enabling DMA mode will result in data being sent only by
|
||
|
|
multiple of 4 packet sizes. This is due to the fact that USB DMA does
|
||
|
|
not allow sending data from non word-aligned addresses.
|
||
|
|
For this specific application, it is advised to not enable this option
|
||
|
|
unless required. */
|
||
|
|
#define USB_OTG_HS_DEDICATED_EP1_ENABLED
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/****************** USB OTG FS CONFIGURATION **********************************/
|
||
|
|
#ifdef USB_OTG_FS_CORE
|
||
|
|
#define RX_FIFO_FS_SIZE 128
|
||
|
|
#define TX0_FIFO_FS_SIZE 32
|
||
|
|
#define TX1_FIFO_FS_SIZE 128
|
||
|
|
#define TX2_FIFO_FS_SIZE 32
|
||
|
|
#define TX3_FIFO_FS_SIZE 0
|
||
|
|
|
||
|
|
// #define USB_OTG_FS_LOW_PWR_MGMT_SUPPORT
|
||
|
|
// #define USB_OTG_FS_SOF_OUTPUT_ENABLED
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/****************** USB OTG MISC CONFIGURATION ********************************/
|
||
|
|
#define VBUS_SENSING_ENABLED
|
||
|
|
|
||
|
|
/****************** USB OTG MODE CONFIGURATION ********************************/
|
||
|
|
//#define USE_HOST_MODE
|
||
|
|
#define USE_DEVICE_MODE
|
||
|
|
//#define USE_OTG_MODE
|
||
|
|
|
||
|
|
#ifndef USB_OTG_FS_CORE
|
||
|
|
#ifndef USB_OTG_HS_CORE
|
||
|
|
#error "USB_OTG_HS_CORE or USB_OTG_FS_CORE should be defined"
|
||
|
|
#endif
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#ifndef USE_DEVICE_MODE
|
||
|
|
#ifndef USE_HOST_MODE
|
||
|
|
#error "USE_DEVICE_MODE or USE_HOST_MODE should be defined"
|
||
|
|
#endif
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#ifndef USE_USB_OTG_HS
|
||
|
|
#ifndef USE_USB_OTG_FS
|
||
|
|
#error "USE_USB_OTG_HS or USE_USB_OTG_FS should be defined"
|
||
|
|
#endif
|
||
|
|
#else //USE_USB_OTG_HS
|
||
|
|
#ifndef USE_ULPI_PHY
|
||
|
|
#ifndef USE_EMBEDDED_PHY
|
||
|
|
#error "USE_ULPI_PHY or USE_EMBEDDED_PHY should be defined"
|
||
|
|
#endif
|
||
|
|
#endif
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/****************** C Compilers dependant keywords ****************************/
|
||
|
|
/* In HS mode and when the DMA is used, all variables and data structures dealing
|
||
|
|
with the DMA during the transaction process should be 4-bytes aligned */
|
||
|
|
#ifdef USB_OTG_HS_INTERNAL_DMA_ENABLED
|
||
|
|
#if defined (__GNUC__) /* GNU Compiler */
|
||
|
|
#define __ALIGN_END __attribute__ ((aligned (4)))
|
||
|
|
#define __ALIGN_BEGIN
|
||
|
|
#else
|
||
|
|
#define __ALIGN_END
|
||
|
|
#if defined (__CC_ARM) /* ARM Compiler */
|
||
|
|
#define __ALIGN_BEGIN __align(4)
|
||
|
|
#elif defined (__ICCARM__) /* IAR Compiler */
|
||
|
|
#define __ALIGN_BEGIN
|
||
|
|
#elif defined (__TASKING__) /* TASKING Compiler */
|
||
|
|
#define __ALIGN_BEGIN __align(4)
|
||
|
|
#endif /* __CC_ARM */
|
||
|
|
#endif /* __GNUC__ */
|
||
|
|
#else
|
||
|
|
#define __ALIGN_BEGIN
|
||
|
|
#define __ALIGN_END
|
||
|
|
#endif /* USB_OTG_HS_INTERNAL_DMA_ENABLED */
|
||
|
|
|
||
|
|
/* __packed keyword used to decrease the data type alignment to 1-byte */
|
||
|
|
#if defined (__CC_ARM) /* ARM Compiler */
|
||
|
|
#define __packed __packed
|
||
|
|
#elif defined (__ICCARM__) /* IAR Compiler */
|
||
|
|
#define __packed __packed
|
||
|
|
#elif defined ( __GNUC__ ) /* GNU Compiler */
|
||
|
|
#define __packed __attribute__ ((__packed__))
|
||
|
|
#elif defined (__TASKING__) /* TASKING Compiler */
|
||
|
|
#define __packed __unaligned
|
||
|
|
#endif /* __CC_ARM */
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @}
|
||
|
|
*/
|
||
|
|
|
||
|
|
|
||
|
|
/** @defgroup USB_CONF_Exported_Types
|
||
|
|
* @{
|
||
|
|
*/
|
||
|
|
/**
|
||
|
|
* @}
|
||
|
|
*/
|
||
|
|
|
||
|
|
|
||
|
|
/** @defgroup USB_CONF_Exported_Macros
|
||
|
|
* @{
|
||
|
|
*/
|
||
|
|
/**
|
||
|
|
* @}
|
||
|
|
*/
|
||
|
|
|
||
|
|
/** @defgroup USB_CONF_Exported_Variables
|
||
|
|
* @{
|
||
|
|
*/
|
||
|
|
/**
|
||
|
|
* @}
|
||
|
|
*/
|
||
|
|
|
||
|
|
/** @defgroup USB_CONF_Exported_FunctionsPrototype
|
||
|
|
* @{
|
||
|
|
*/
|
||
|
|
/**
|
||
|
|
* @}
|
||
|
|
*/
|
||
|
|
|
||
|
|
|
||
|
|
#endif //__USB_CONF__H__
|
||
|
|
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @}
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* @}
|
||
|
|
*/
|
||
|
|
|
||
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
||
|
|
|