stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
/*
|
|
|
|
* This file is part of the MicroPython project, http://micropython.org/
|
|
|
|
*
|
|
|
|
* The MIT License (MIT)
|
|
|
|
*
|
|
|
|
* Copyright (c) 2014-2018 Damien P. George
|
|
|
|
*
|
|
|
|
* Permission is hereby granted, free of charge, to any person obtaining a copy
|
|
|
|
* of this software and associated documentation files (the "Software"), to deal
|
|
|
|
* in the Software without restriction, including without limitation the rights
|
|
|
|
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
|
|
|
* copies of the Software, and to permit persons to whom the Software is
|
|
|
|
* furnished to do so, subject to the following conditions:
|
|
|
|
*
|
|
|
|
* The above copyright notice and this permission notice shall be included in
|
|
|
|
* all copies or substantial portions of the Software.
|
|
|
|
*
|
|
|
|
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
|
|
|
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
|
|
|
|
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
|
|
|
|
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
|
|
|
|
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
|
|
|
|
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
|
|
|
|
* THE SOFTWARE.
|
|
|
|
*/
|
|
|
|
|
|
|
|
#include <stdio.h>
|
2019-04-05 07:35:04 -04:00
|
|
|
#include <string.h>
|
|
|
|
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
#include "py/runtime.h"
|
|
|
|
#include "py/mphal.h"
|
2021-08-22 11:26:13 -04:00
|
|
|
#include "extmod/modnetwork.h"
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
#include "spi.h"
|
|
|
|
|
|
|
|
#if MICROPY_PY_WIZNET5K && MICROPY_PY_LWIP
|
|
|
|
|
2021-07-09 00:19:15 -04:00
|
|
|
#include "shared/netutils/netutils.h"
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
#include "drivers/wiznet5k/ethernet/socket.h"
|
|
|
|
#include "lwip/err.h"
|
|
|
|
#include "lwip/dns.h"
|
|
|
|
#include "lwip/dhcp.h"
|
|
|
|
#include "netif/etharp.h"
|
|
|
|
|
2019-04-05 07:33:49 -04:00
|
|
|
#define TRACE_ETH_TX (0x0002)
|
|
|
|
#define TRACE_ETH_RX (0x0004)
|
|
|
|
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
/*******************************************************************************/
|
|
|
|
// Wiznet5k Ethernet driver in MACRAW mode
|
|
|
|
|
|
|
|
typedef struct _wiznet5k_obj_t {
|
2019-06-03 03:06:35 -04:00
|
|
|
mp_obj_base_t base;
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
mp_uint_t cris_state;
|
|
|
|
const spi_t *spi;
|
|
|
|
mp_hal_pin_obj_t cs;
|
|
|
|
mp_hal_pin_obj_t rst;
|
|
|
|
uint8_t eth_frame[1514];
|
2019-04-05 07:33:49 -04:00
|
|
|
uint32_t trace_flags;
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
struct netif netif;
|
|
|
|
struct dhcp dhcp_struct;
|
|
|
|
} wiznet5k_obj_t;
|
|
|
|
|
|
|
|
// Global object holding the Wiznet5k state
|
|
|
|
STATIC wiznet5k_obj_t wiznet5k_obj;
|
|
|
|
|
|
|
|
STATIC void wiznet5k_lwip_init(wiznet5k_obj_t *self);
|
|
|
|
|
|
|
|
STATIC void wiz_cris_enter(void) {
|
|
|
|
wiznet5k_obj.cris_state = MICROPY_BEGIN_ATOMIC_SECTION();
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC void wiz_cris_exit(void) {
|
|
|
|
MICROPY_END_ATOMIC_SECTION(wiznet5k_obj.cris_state);
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC void wiz_cs_select(void) {
|
|
|
|
mp_hal_pin_low(wiznet5k_obj.cs);
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC void wiz_cs_deselect(void) {
|
|
|
|
mp_hal_pin_high(wiznet5k_obj.cs);
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC void wiz_spi_read(uint8_t *buf, uint32_t len) {
|
|
|
|
HAL_StatusTypeDef status = HAL_SPI_Receive(wiznet5k_obj.spi->spi, buf, len, 5000);
|
|
|
|
(void)status;
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC void wiz_spi_write(const uint8_t *buf, uint32_t len) {
|
2020-02-26 23:36:53 -05:00
|
|
|
HAL_StatusTypeDef status = HAL_SPI_Transmit(wiznet5k_obj.spi->spi, (uint8_t *)buf, len, 5000);
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
(void)status;
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC void wiznet5k_init(void) {
|
|
|
|
// SPI configuration
|
|
|
|
SPI_InitTypeDef *init = &wiznet5k_obj.spi->spi->Init;
|
|
|
|
init->Mode = SPI_MODE_MASTER;
|
|
|
|
init->Direction = SPI_DIRECTION_2LINES;
|
|
|
|
init->DataSize = SPI_DATASIZE_8BIT;
|
|
|
|
init->CLKPolarity = SPI_POLARITY_LOW; // clock is low when idle
|
|
|
|
init->CLKPhase = SPI_PHASE_1EDGE; // data latched on first edge, which is rising edge for low-idle
|
|
|
|
init->NSS = SPI_NSS_SOFT;
|
|
|
|
init->BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2; // clock freq = f_PCLK / this_prescale_value; Wiz820i can do up to 80MHz
|
|
|
|
init->FirstBit = SPI_FIRSTBIT_MSB;
|
|
|
|
init->TIMode = SPI_TIMODE_DISABLED;
|
|
|
|
init->CRCCalculation = SPI_CRCCALCULATION_DISABLED;
|
|
|
|
init->CRCPolynomial = 7; // unused
|
|
|
|
spi_init(wiznet5k_obj.spi, false);
|
|
|
|
|
|
|
|
mp_hal_pin_output(wiznet5k_obj.cs);
|
|
|
|
mp_hal_pin_output(wiznet5k_obj.rst);
|
|
|
|
|
|
|
|
// Reset the chip
|
|
|
|
mp_hal_pin_low(wiznet5k_obj.rst);
|
|
|
|
mp_hal_delay_ms(1); // datasheet says 2us
|
|
|
|
mp_hal_pin_high(wiznet5k_obj.rst);
|
|
|
|
mp_hal_delay_ms(150); // datasheet says 150ms
|
|
|
|
|
|
|
|
// Set physical interface callbacks
|
|
|
|
reg_wizchip_cris_cbfunc(wiz_cris_enter, wiz_cris_exit);
|
|
|
|
reg_wizchip_cs_cbfunc(wiz_cs_select, wiz_cs_deselect);
|
|
|
|
reg_wizchip_spi_cbfunc(wiz_spi_read, wiz_spi_write);
|
|
|
|
|
|
|
|
// Configure 16k buffers for fast MACRAW
|
|
|
|
uint8_t sn_size[16] = {16, 0, 0, 0, 0, 0, 0, 0, 16, 0, 0, 0, 0, 0, 0, 0};
|
|
|
|
ctlwizchip(CW_INIT_WIZCHIP, sn_size);
|
|
|
|
|
|
|
|
// Seems we need a small delay after init
|
|
|
|
mp_hal_delay_ms(250);
|
|
|
|
|
2019-04-05 07:37:06 -04:00
|
|
|
// If the device doesn't have a MAC address then set one
|
|
|
|
uint8_t mac[6];
|
|
|
|
getSHAR(mac);
|
|
|
|
if ((mac[0] | mac[1] | mac[2] | mac[3] | mac[4] | mac[5]) == 0) {
|
|
|
|
mp_hal_get_mac(MP_HAL_MAC_ETH0, mac);
|
|
|
|
setSHAR(mac);
|
|
|
|
}
|
|
|
|
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
// Hook the Wiznet into lwIP
|
|
|
|
wiznet5k_lwip_init(&wiznet5k_obj);
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC void wiznet5k_deinit(void) {
|
|
|
|
for (struct netif *netif = netif_list; netif != NULL; netif = netif->next) {
|
|
|
|
if (netif == &wiznet5k_obj.netif) {
|
|
|
|
netif_remove(netif);
|
|
|
|
netif->flags = 0;
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC void wiznet5k_get_mac_address(wiznet5k_obj_t *self, uint8_t mac[6]) {
|
|
|
|
(void)self;
|
|
|
|
getSHAR(mac);
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC void wiznet5k_send_ethernet(wiznet5k_obj_t *self, size_t len, const uint8_t *buf) {
|
|
|
|
uint8_t ip[4] = {1, 1, 1, 1}; // dummy
|
2020-02-26 23:36:53 -05:00
|
|
|
int ret = WIZCHIP_EXPORT(sendto)(0, (byte *)buf, len, ip, 11); // dummy port
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
if (ret != len) {
|
|
|
|
printf("wiznet5k_send_ethernet: fatal error %d\n", ret);
|
|
|
|
netif_set_link_down(&self->netif);
|
|
|
|
netif_set_down(&self->netif);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
// Stores the frame in self->eth_frame and returns number of bytes in the frame, 0 for no frame
|
|
|
|
STATIC uint16_t wiznet5k_recv_ethernet(wiznet5k_obj_t *self) {
|
|
|
|
uint16_t len = getSn_RX_RSR(0);
|
|
|
|
if (len == 0) {
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
byte ip[4];
|
|
|
|
uint16_t port;
|
|
|
|
int ret = WIZCHIP_EXPORT(recvfrom)(0, self->eth_frame, 1514, ip, &port);
|
|
|
|
if (ret <= 0) {
|
2019-06-03 03:06:35 -04:00
|
|
|
printf("wiznet5k_poll: fatal error len=%u ret=%d\n", len, ret);
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
netif_set_link_down(&self->netif);
|
|
|
|
netif_set_down(&self->netif);
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
/*******************************************************************************/
|
|
|
|
// Wiznet5k lwIP interface
|
|
|
|
|
|
|
|
STATIC err_t wiznet5k_netif_output(struct netif *netif, struct pbuf *p) {
|
|
|
|
wiznet5k_obj_t *self = netif->state;
|
|
|
|
pbuf_copy_partial(p, self->eth_frame, p->tot_len, 0);
|
2019-04-05 07:33:49 -04:00
|
|
|
if (self->trace_flags & TRACE_ETH_TX) {
|
|
|
|
netutils_ethernet_trace(MP_PYTHON_PRINTER, p->tot_len, self->eth_frame, NETUTILS_TRACE_IS_TX | NETUTILS_TRACE_NEWLINE);
|
|
|
|
}
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
wiznet5k_send_ethernet(self, p->tot_len, self->eth_frame);
|
|
|
|
return ERR_OK;
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC err_t wiznet5k_netif_init(struct netif *netif) {
|
|
|
|
netif->linkoutput = wiznet5k_netif_output;
|
|
|
|
netif->output = etharp_output;
|
|
|
|
netif->mtu = 1500;
|
|
|
|
netif->flags = NETIF_FLAG_BROADCAST | NETIF_FLAG_ETHARP | NETIF_FLAG_ETHERNET | NETIF_FLAG_IGMP;
|
|
|
|
wiznet5k_get_mac_address(netif->state, netif->hwaddr);
|
|
|
|
netif->hwaddr_len = sizeof(netif->hwaddr);
|
|
|
|
int ret = WIZCHIP_EXPORT(socket)(0, Sn_MR_MACRAW, 0, 0);
|
|
|
|
if (ret != 0) {
|
|
|
|
printf("WIZNET fatal error in netifinit: %d\n", ret);
|
|
|
|
return ERR_IF;
|
|
|
|
}
|
|
|
|
|
|
|
|
// Enable MAC filtering so we only get frames destined for us, to reduce load on lwIP
|
|
|
|
setSn_MR(0, getSn_MR(0) | Sn_MR_MFEN);
|
|
|
|
|
|
|
|
return ERR_OK;
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC void wiznet5k_lwip_init(wiznet5k_obj_t *self) {
|
|
|
|
ip_addr_t ipconfig[4];
|
|
|
|
ipconfig[0].addr = 0;
|
|
|
|
ipconfig[1].addr = 0;
|
|
|
|
ipconfig[2].addr = 0;
|
|
|
|
ipconfig[3].addr = 0;
|
|
|
|
netif_add(&self->netif, &ipconfig[0], &ipconfig[1], &ipconfig[2], self, wiznet5k_netif_init, ethernet_input);
|
|
|
|
self->netif.name[0] = 'e';
|
|
|
|
self->netif.name[1] = '0';
|
|
|
|
netif_set_default(&self->netif);
|
|
|
|
dns_setserver(0, &ipconfig[3]);
|
|
|
|
dhcp_set_struct(&self->netif, &self->dhcp_struct);
|
|
|
|
// Setting NETIF_FLAG_UP then clearing it is a workaround for dhcp_start and the
|
|
|
|
// LWIP_DHCP_CHECK_LINK_UP option, so that the DHCP client schedules itself to
|
|
|
|
// automatically start when the interface later goes up.
|
|
|
|
self->netif.flags |= NETIF_FLAG_UP;
|
|
|
|
dhcp_start(&self->netif);
|
|
|
|
self->netif.flags &= ~NETIF_FLAG_UP;
|
|
|
|
}
|
|
|
|
|
2019-06-03 03:06:35 -04:00
|
|
|
void wiznet5k_poll(void) {
|
|
|
|
wiznet5k_obj_t *self = &wiznet5k_obj;
|
|
|
|
if (!(self->netif.flags & NETIF_FLAG_LINK_UP)) {
|
|
|
|
return;
|
|
|
|
}
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
uint16_t len;
|
|
|
|
while ((len = wiznet5k_recv_ethernet(self)) > 0) {
|
2019-04-05 07:33:49 -04:00
|
|
|
if (self->trace_flags & TRACE_ETH_RX) {
|
|
|
|
netutils_ethernet_trace(MP_PYTHON_PRINTER, len, self->eth_frame, NETUTILS_TRACE_NEWLINE);
|
|
|
|
}
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
struct pbuf *p = pbuf_alloc(PBUF_RAW, len, PBUF_POOL);
|
|
|
|
if (p != NULL) {
|
|
|
|
pbuf_take(p, self->eth_frame, len);
|
|
|
|
if (self->netif.input(p, &self->netif) != ERR_OK) {
|
|
|
|
pbuf_free(p);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
/*******************************************************************************/
|
|
|
|
// MicroPython bindings
|
|
|
|
|
|
|
|
// WIZNET5K([spi, pin_cs, pin_rst])
|
|
|
|
STATIC mp_obj_t wiznet5k_make_new(const mp_obj_type_t *type, size_t n_args, size_t n_kw, const mp_obj_t *args) {
|
|
|
|
// check arguments
|
|
|
|
mp_arg_check_num(n_args, n_kw, 3, 3, false);
|
|
|
|
|
|
|
|
const spi_t *spi = spi_from_mp_obj(args[0]);
|
|
|
|
mp_hal_pin_obj_t cs = pin_find(args[1]);
|
|
|
|
mp_hal_pin_obj_t rst = pin_find(args[2]);
|
|
|
|
|
|
|
|
// Access the existing object, if it has been constructed with the same hardware interface
|
2019-06-03 03:06:35 -04:00
|
|
|
if (wiznet5k_obj.base.type == &mod_network_nic_type_wiznet5k) {
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
if (!(wiznet5k_obj.spi == spi && wiznet5k_obj.cs == cs && wiznet5k_obj.rst == rst
|
2020-02-26 23:36:53 -05:00
|
|
|
&& wiznet5k_obj.netif.flags != 0)) {
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
wiznet5k_deinit();
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
// Init the wiznet5k object
|
2019-06-03 03:06:35 -04:00
|
|
|
wiznet5k_obj.base.type = &mod_network_nic_type_wiznet5k;
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
wiznet5k_obj.cris_state = 0;
|
|
|
|
wiznet5k_obj.spi = spi;
|
|
|
|
wiznet5k_obj.cs = cs;
|
|
|
|
wiznet5k_obj.rst = rst;
|
2019-04-05 07:33:49 -04:00
|
|
|
wiznet5k_obj.trace_flags = 0;
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
|
|
|
|
// Return wiznet5k object
|
|
|
|
return MP_OBJ_FROM_PTR(&wiznet5k_obj);
|
|
|
|
}
|
|
|
|
|
|
|
|
STATIC mp_obj_t wiznet5k_regs(mp_obj_t self_in) {
|
|
|
|
(void)self_in;
|
|
|
|
printf("Wiz CREG:");
|
|
|
|
for (int i = 0; i < 0x50; ++i) {
|
|
|
|
if (i % 16 == 0) {
|
|
|
|
printf("\n %04x:", i);
|
|
|
|
}
|
|
|
|
#if MICROPY_PY_WIZNET5K == 5200
|
|
|
|
uint32_t reg = i;
|
|
|
|
#else
|
|
|
|
uint32_t reg = _W5500_IO_BASE_ | i << 8;
|
|
|
|
#endif
|
|
|
|
printf(" %02x", WIZCHIP_READ(reg));
|
|
|
|
}
|
|
|
|
for (int sn = 0; sn < 4; ++sn) {
|
|
|
|
printf("\nWiz SREG[%d]:", sn);
|
|
|
|
for (int i = 0; i < 0x30; ++i) {
|
|
|
|
if (i % 16 == 0) {
|
|
|
|
printf("\n %04x:", i);
|
|
|
|
}
|
|
|
|
#if MICROPY_PY_WIZNET5K == 5200
|
|
|
|
uint32_t reg = WIZCHIP_SREG_ADDR(sn, i);
|
|
|
|
#else
|
|
|
|
uint32_t reg = _W5500_IO_BASE_ | i << 8 | WIZCHIP_SREG_BLOCK(sn) << 3;
|
|
|
|
#endif
|
|
|
|
printf(" %02x", WIZCHIP_READ(reg));
|
|
|
|
}
|
|
|
|
}
|
|
|
|
printf("\n");
|
|
|
|
return mp_const_none;
|
|
|
|
}
|
|
|
|
STATIC MP_DEFINE_CONST_FUN_OBJ_1(wiznet5k_regs_obj, wiznet5k_regs);
|
|
|
|
|
|
|
|
STATIC mp_obj_t wiznet5k_isconnected(mp_obj_t self_in) {
|
|
|
|
wiznet5k_obj_t *self = MP_OBJ_TO_PTR(self_in);
|
|
|
|
return mp_obj_new_bool(
|
|
|
|
wizphy_getphylink() == PHY_LINK_ON
|
|
|
|
&& (self->netif.flags & NETIF_FLAG_UP)
|
|
|
|
&& self->netif.ip_addr.addr != 0
|
2020-02-26 23:36:53 -05:00
|
|
|
);
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
}
|
|
|
|
STATIC MP_DEFINE_CONST_FUN_OBJ_1(wiznet5k_isconnected_obj, wiznet5k_isconnected);
|
|
|
|
|
|
|
|
STATIC mp_obj_t wiznet5k_active(size_t n_args, const mp_obj_t *args) {
|
|
|
|
wiznet5k_obj_t *self = MP_OBJ_TO_PTR(args[0]);
|
|
|
|
if (n_args == 1) {
|
|
|
|
return mp_obj_new_bool(self->netif.flags & NETIF_FLAG_UP);
|
|
|
|
} else {
|
|
|
|
if (mp_obj_is_true(args[1])) {
|
|
|
|
if (!(self->netif.flags & NETIF_FLAG_UP)) {
|
|
|
|
wiznet5k_init();
|
|
|
|
netif_set_link_up(&self->netif);
|
|
|
|
netif_set_up(&self->netif);
|
|
|
|
}
|
|
|
|
} else {
|
|
|
|
if (self->netif.flags & NETIF_FLAG_UP) {
|
|
|
|
netif_set_down(&self->netif);
|
|
|
|
netif_set_link_down(&self->netif);
|
|
|
|
wiznet5k_deinit();
|
|
|
|
}
|
|
|
|
}
|
|
|
|
return mp_const_none;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
STATIC MP_DEFINE_CONST_FUN_OBJ_VAR_BETWEEN(wiznet5k_active_obj, 1, 2, wiznet5k_active);
|
|
|
|
|
|
|
|
STATIC mp_obj_t wiznet5k_ifconfig(size_t n_args, const mp_obj_t *args) {
|
|
|
|
wiznet5k_obj_t *self = MP_OBJ_TO_PTR(args[0]);
|
|
|
|
return mod_network_nic_ifconfig(&self->netif, n_args - 1, args + 1);
|
|
|
|
}
|
|
|
|
STATIC MP_DEFINE_CONST_FUN_OBJ_VAR_BETWEEN(wiznet5k_ifconfig_obj, 1, 2, wiznet5k_ifconfig);
|
|
|
|
|
|
|
|
STATIC mp_obj_t wiznet5k_status(size_t n_args, const mp_obj_t *args) {
|
|
|
|
wiznet5k_obj_t *self = MP_OBJ_TO_PTR(args[0]);
|
|
|
|
(void)self;
|
|
|
|
|
|
|
|
if (n_args == 1) {
|
|
|
|
// No arguments: return link status
|
|
|
|
if (self->netif.flags && wizphy_getphylink() == PHY_LINK_ON) {
|
|
|
|
if ((self->netif.flags & NETIF_FLAG_UP) && self->netif.ip_addr.addr != 0) {
|
|
|
|
return MP_OBJ_NEW_SMALL_INT(2);
|
|
|
|
} else {
|
|
|
|
return MP_OBJ_NEW_SMALL_INT(1);
|
|
|
|
}
|
|
|
|
} else {
|
|
|
|
return MP_OBJ_NEW_SMALL_INT(0);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
2020-03-02 06:35:22 -05:00
|
|
|
mp_raise_ValueError(MP_ERROR_TEXT("unknown config param"));
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
}
|
|
|
|
STATIC MP_DEFINE_CONST_FUN_OBJ_VAR_BETWEEN(wiznet5k_status_obj, 1, 2, wiznet5k_status);
|
|
|
|
|
|
|
|
STATIC mp_obj_t wiznet5k_config(size_t n_args, const mp_obj_t *args, mp_map_t *kwargs) {
|
|
|
|
wiznet5k_obj_t *self = MP_OBJ_TO_PTR(args[0]);
|
|
|
|
|
|
|
|
if (kwargs->used == 0) {
|
|
|
|
// Get config value
|
|
|
|
if (n_args != 2) {
|
2020-03-02 06:35:22 -05:00
|
|
|
mp_raise_TypeError(MP_ERROR_TEXT("must query one param"));
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
}
|
|
|
|
|
|
|
|
switch (mp_obj_str_get_qstr(args[1])) {
|
|
|
|
case MP_QSTR_mac: {
|
|
|
|
uint8_t buf[6];
|
|
|
|
wiznet5k_get_mac_address(self, buf);
|
|
|
|
return mp_obj_new_bytes(buf, 6);
|
|
|
|
}
|
|
|
|
default:
|
2020-03-02 06:35:22 -05:00
|
|
|
mp_raise_ValueError(MP_ERROR_TEXT("unknown config param"));
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
}
|
|
|
|
} else {
|
|
|
|
// Set config value(s)
|
|
|
|
if (n_args != 1) {
|
2020-03-02 06:35:22 -05:00
|
|
|
mp_raise_TypeError(MP_ERROR_TEXT("can't specify pos and kw args"));
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
}
|
2019-04-05 07:33:49 -04:00
|
|
|
|
|
|
|
for (size_t i = 0; i < kwargs->alloc; ++i) {
|
|
|
|
if (MP_MAP_SLOT_IS_FILLED(kwargs, i)) {
|
|
|
|
mp_map_elem_t *e = &kwargs->table[i];
|
|
|
|
switch (mp_obj_str_get_qstr(e->key)) {
|
2019-04-05 07:35:04 -04:00
|
|
|
case MP_QSTR_mac: {
|
|
|
|
mp_buffer_info_t buf;
|
|
|
|
mp_get_buffer_raise(e->value, &buf, MP_BUFFER_READ);
|
|
|
|
if (buf.len != 6) {
|
|
|
|
mp_raise_ValueError(NULL);
|
|
|
|
}
|
|
|
|
setSHAR(buf.buf);
|
|
|
|
memcpy(self->netif.hwaddr, buf.buf, 6);
|
|
|
|
break;
|
|
|
|
}
|
2019-04-05 07:33:49 -04:00
|
|
|
case MP_QSTR_trace: {
|
|
|
|
self->trace_flags = mp_obj_get_int(e->value);
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
default:
|
2020-03-02 06:35:22 -05:00
|
|
|
mp_raise_ValueError(MP_ERROR_TEXT("unknown config param"));
|
2019-04-05 07:33:49 -04:00
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
return mp_const_none;
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
}
|
|
|
|
}
|
|
|
|
STATIC MP_DEFINE_CONST_FUN_OBJ_KW(wiznet5k_config_obj, 1, wiznet5k_config);
|
|
|
|
|
|
|
|
STATIC mp_obj_t send_ethernet_wrapper(mp_obj_t self_in, mp_obj_t buf_in) {
|
|
|
|
wiznet5k_obj_t *self = MP_OBJ_TO_PTR(self_in);
|
|
|
|
mp_buffer_info_t buf;
|
|
|
|
mp_get_buffer_raise(buf_in, &buf, MP_BUFFER_READ);
|
|
|
|
wiznet5k_send_ethernet(self, buf.len, buf.buf);
|
|
|
|
return mp_const_none;
|
|
|
|
}
|
|
|
|
STATIC MP_DEFINE_CONST_FUN_OBJ_2(send_ethernet_obj, send_ethernet_wrapper);
|
|
|
|
|
|
|
|
STATIC const mp_rom_map_elem_t wiznet5k_locals_dict_table[] = {
|
|
|
|
{ MP_ROM_QSTR(MP_QSTR_regs), MP_ROM_PTR(&wiznet5k_regs_obj) },
|
|
|
|
{ MP_ROM_QSTR(MP_QSTR_isconnected), MP_ROM_PTR(&wiznet5k_isconnected_obj) },
|
|
|
|
{ MP_ROM_QSTR(MP_QSTR_active), MP_ROM_PTR(&wiznet5k_active_obj) },
|
|
|
|
{ MP_ROM_QSTR(MP_QSTR_ifconfig), MP_ROM_PTR(&wiznet5k_ifconfig_obj) },
|
|
|
|
{ MP_ROM_QSTR(MP_QSTR_status), MP_ROM_PTR(&wiznet5k_status_obj) },
|
|
|
|
{ MP_ROM_QSTR(MP_QSTR_config), MP_ROM_PTR(&wiznet5k_config_obj) },
|
|
|
|
|
|
|
|
{ MP_ROM_QSTR(MP_QSTR_send_ethernet), MP_ROM_PTR(&send_ethernet_obj) },
|
|
|
|
};
|
|
|
|
STATIC MP_DEFINE_CONST_DICT(wiznet5k_locals_dict, wiznet5k_locals_dict_table);
|
|
|
|
|
|
|
|
const mp_obj_type_t mod_network_nic_type_wiznet5k = {
|
|
|
|
{ &mp_type_type },
|
|
|
|
.name = MP_QSTR_WIZNET5K,
|
|
|
|
.make_new = wiznet5k_make_new,
|
2020-02-26 23:36:53 -05:00
|
|
|
.locals_dict = (mp_obj_dict_t *)&wiznet5k_locals_dict,
|
stm32: Add network driver for Wiznet5k using MACRAW mode and lwIP.
The Wiznet5k series of chips support a MACRAW mode which allows the host to
send and receive Ethernet frames directly. This can be hooked into the
lwIP stack to provide a full "socket" implementation using this Wiznet
Ethernet device. This patch adds support for this feature.
To enable the feature one must add the following to mpconfigboard.mk, or
mpconfigport.mk:
MICROPY_PY_WIZNET5K = 5500
and the following to mpconfigboard.h, or mpconfigport.h:
#define MICROPY_PY_LWIP (1)
After wiring up the module (X5=CS, X4=RST), usage on a pyboard is:
import time, network
nic = network.WIZNET5K(pyb.SPI(1), pyb.Pin.board.X5, pyb.Pin.board.X4)
nic.active(1)
while not nic.isconnected():
time.sleep_ms(50) # needed to poll the NIC
print(nic.ifconfig())
Then use the socket module as usual.
Compared to using the built-in TCP/IP stack on the Wiznet module, some
performance is lost in MACRAW mode: with a lot of memory allocated to lwIP
buffers, lwIP gives Around 750,000 bytes/sec max TCP download, compared
with 1M/sec when using the TCP/IP stack on the Wiznet module.
2018-06-01 00:21:38 -04:00
|
|
|
};
|
|
|
|
|
|
|
|
#endif // MICROPY_PY_WIZNET5K && MICROPY_PY_LWIP
|