2015-06-24 19:21:35 -04:00
|
|
|
Floating Point instructions
|
|
|
|
|
==============================
|
|
|
|
|
|
|
|
|
|
These instructions support the use of the ARM floating point coprocessor
|
|
|
|
|
(on platforms such as the Pyboard which are equipped with one). The FPU
|
|
|
|
|
has 32 registers known as ``s0-s31`` each of which can hold a single
|
|
|
|
|
precision float. Data can be passed between the FPU registers and the
|
|
|
|
|
ARM core registers with the ``vmov`` instruction.
|
|
|
|
|
|
|
|
|
|
Note that MicroPython doesn't support passing floats to
|
|
|
|
|
assembler functions, nor can you put a float into ``r0`` and expect a
|
|
|
|
|
reasonable result. There are two ways to overcome this. The first is to
|
|
|
|
|
use arrays, and the second is to pass and/or return integers and convert
|
|
|
|
|
to and from floats in code.
|
|
|
|
|
|
|
|
|
|
Document conventions
|
|
|
|
|
--------------------
|
|
|
|
|
|
|
|
|
|
Notation: ``Sd, Sm, Sn`` denote FPU registers, ``Rd, Rm, Rn`` denote ARM core
|
|
|
|
|
registers. The latter can be any ARM core register although registers
|
|
|
|
|
``R13-R15`` are unlikely to be appropriate in this context.
|
|
|
|
|
|
|
|
|
|
Arithmetic
|
|
|
|
|
----------
|
|
|
|
|
|
|
|
|
|
* vadd(Sd, Sn, Sm) ``Sd = Sn + Sm``
|
|
|
|
|
* vsub(Sd, Sn, Sm) ``Sd = Sn - Sm``
|
|
|
|
|
* vneg(Sd, Sm) ``Sd = -Sm``
|
|
|
|
|
* vmul(Sd, Sn, Sm) ``Sd = Sn * Sm``
|
|
|
|
|
* vdiv(Sd, Sn, Sm) ``Sd = Sn / Sm``
|
|
|
|
|
* vsqrt(Sd, Sm) ``Sd = sqrt(Sm)``
|
|
|
|
|
|
|
|
|
|
Registers may be identical: ``vmul(S0, S0, S0)`` will execute ``S0 = S0*S0``
|
2019-12-03 23:02:54 -05:00
|
|
|
|
2015-06-24 19:21:35 -04:00
|
|
|
Move between ARM core and FPU registers
|
|
|
|
|
---------------------------------------
|
|
|
|
|
|
|
|
|
|
* vmov(Sd, Rm) ``Sd = Rm``
|
|
|
|
|
* vmov(Rd, Sm) ``Rd = Sm``
|
|
|
|
|
|
|
|
|
|
The FPU has a register known as FPSCR, similar to the ARM core's APSR, which stores condition
|
|
|
|
|
codes plus other data. The following instructions provide access to this.
|
2019-12-03 23:02:54 -05:00
|
|
|
|
2015-06-24 19:21:35 -04:00
|
|
|
* vmrs(APSR\_nzcv, FPSCR)
|
|
|
|
|
|
|
|
|
|
Move the floating-point N, Z, C, and V flags to the APSR N, Z, C, and V flags.
|
|
|
|
|
|
|
|
|
|
This is done after an instruction such as an FPU
|
|
|
|
|
comparison to enable the condition codes to be tested by the assembler
|
|
|
|
|
code. The following is a more general form of the instruction.
|
|
|
|
|
|
|
|
|
|
* vmrs(Rd, FPSCR) ``Rd = FPSCR``
|
|
|
|
|
|
|
|
|
|
Move between FPU register and memory
|
|
|
|
|
------------------------------------
|
|
|
|
|
|
|
|
|
|
* vldr(Sd, [Rn, offset]) ``Sd = [Rn + offset]``
|
|
|
|
|
* vstr(Sd, [Rn, offset]) ``[Rn + offset] = Sd``
|
|
|
|
|
|
|
|
|
|
Where ``[Rn + offset]`` denotes the memory address obtained by adding Rn to the offset. This
|
|
|
|
|
is specified in bytes. Since each float value occupies a 32 bit word, when accessing arrays of
|
|
|
|
|
floats the offset must always be a multiple of four bytes.
|
|
|
|
|
|
|
|
|
|
Data Comparison
|
|
|
|
|
---------------
|
|
|
|
|
|
|
|
|
|
* vcmp(Sd, Sm)
|
|
|
|
|
|
|
|
|
|
Compare the values in Sd and Sm and set the FPU N, Z,
|
|
|
|
|
C, and V flags. This would normally be followed by ``vmrs(APSR_nzcv, FPSCR)``
|
|
|
|
|
to enable the results to be tested.
|
|
|
|
|
|
|
|
|
|
Convert between integer and float
|
|
|
|
|
---------------------------------
|
|
|
|
|
|
|
|
|
|
* vcvt\_f32\_s32(Sd, Sm) ``Sd = float(Sm)``
|
|
|
|
|
* vcvt\_s32\_f32(Sd, Sm) ``Sd = int(Sm)``
|
