102 lines
3.8 KiB
C
102 lines
3.8 KiB
C
|
#define MICROPY_HW_BOARD_NAME "NUCLEO-F413ZH"
|
||
|
|
#define MICROPY_HW_MCU_NAME "STM32F413"
|
||
|
|
|
||
|
|
#define MICROPY_HW_HAS_SWITCH (1)
|
||
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
||
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
||
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
||
|
|
#define MICROPY_HW_ENABLE_DAC (1)
|
||
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
||
|
|
|
||
|
|
// HSE is 8MHz, CPU freq set to 96MHz
|
||
|
|
#define MICROPY_HW_CLK_PLLM (8)
|
||
|
|
#define MICROPY_HW_CLK_PLLN (192)
|
||
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
|
||
|
|
#define MICROPY_HW_CLK_PLLQ (4)
|
||
|
|
|
||
|
|
// For 2.7 to 3.6 V, 75 to 100 MHz: 3 wait states.
|
||
|
|
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_3
|
||
|
|
|
||
|
|
// UART config
|
||
|
|
#define MICROPY_HW_UART1_TX (pin_B6)
|
||
|
|
#define MICROPY_HW_UART1_RX (pin_B3) // shared with CAN3
|
||
|
|
#define MICROPY_HW_UART2_TX (pin_D5)
|
||
|
|
#define MICROPY_HW_UART2_RX (pin_D6)
|
||
|
|
#define MICROPY_HW_UART3_TX (pin_D8)
|
||
|
|
#define MICROPY_HW_UART3_RX (pin_D9)
|
||
|
|
#define MICROPY_HW_UART4_TX (pin_D1)
|
||
|
|
#define MICROPY_HW_UART4_RX (pin_D0)
|
||
|
|
#define MICROPY_HW_UART5_TX (pin_C12)
|
||
|
|
#define MICROPY_HW_UART5_RX (pin_D2)
|
||
|
|
#define MICROPY_HW_UART6_TX (pin_G14)
|
||
|
|
#define MICROPY_HW_UART6_RX (pin_G9)
|
||
|
|
#define MICROPY_HW_UART7_TX (pin_E8)
|
||
|
|
#define MICROPY_HW_UART7_RX (pin_E7)
|
||
|
|
#define MICROPY_HW_UART8_TX (pin_E1)
|
||
|
|
#define MICROPY_HW_UART8_RX (pin_E0)
|
||
|
|
#define MICROPY_HW_UART9_TX (pin_D15)
|
||
|
|
#define MICROPY_HW_UART9_RX (pin_D14)
|
||
|
|
#define MICROPY_HW_UART10_TX (pin_E3)
|
||
|
|
#define MICROPY_HW_UART10_RX (pin_E2)
|
||
|
|
#define MICROPY_HW_UART_REPL PYB_UART_3
|
||
|
|
#define MICROPY_HW_UART_REPL_BAUD 115200
|
||
|
|
|
||
|
|
// I2C busses
|
||
|
|
#define MICROPY_HW_I2C1_SCL (pin_B8)
|
||
|
|
#define MICROPY_HW_I2C1_SDA (pin_B9)
|
||
|
|
#define MICROPY_HW_I2C2_SCL (pin_F1)
|
||
|
|
#define MICROPY_HW_I2C2_SDA (pin_F0)
|
||
|
|
#define MICROPY_HW_I2C3_SCL (pin_A8)
|
||
|
|
#define MICROPY_HW_I2C3_SDA (pin_C9)
|
||
|
|
|
||
|
|
// SPI busses
|
||
|
|
#define MICROPY_HW_SPI1_NSS (pin_A4) // shared with DAC
|
||
|
|
#define MICROPY_HW_SPI1_SCK (pin_A5) // shared with DAC
|
||
|
|
#define MICROPY_HW_SPI1_MISO (pin_A6)
|
||
|
|
#define MICROPY_HW_SPI1_MOSI (pin_A7)
|
||
|
|
#define MICROPY_HW_SPI2_NSS (pin_B12)
|
||
|
|
#define MICROPY_HW_SPI2_SCK (pin_C7)
|
||
|
|
#define MICROPY_HW_SPI2_MISO (pin_C2)
|
||
|
|
#define MICROPY_HW_SPI2_MOSI (pin_C3)
|
||
|
|
#define MICROPY_HW_SPI3_NSS (pin_A15)
|
||
|
|
#define MICROPY_HW_SPI3_SCK (pin_C10)
|
||
|
|
#define MICROPY_HW_SPI3_MISO (pin_C11)
|
||
|
|
#define MICROPY_HW_SPI3_MOSI (pin_B5)
|
||
|
|
#define MICROPY_HW_SPI4_NSS (pin_E4)
|
||
|
|
#define MICROPY_HW_SPI4_SCK (pin_B13)
|
||
|
|
#define MICROPY_HW_SPI4_MISO (pin_E5)
|
||
|
|
#define MICROPY_HW_SPI4_MOSI (pin_E6)
|
||
|
|
#define MICROPY_HW_SPI5_NSS (pin_E11)
|
||
|
|
#define MICROPY_HW_SPI5_SCK (pin_E12)
|
||
|
|
#define MICROPY_HW_SPI5_MISO (pin_E13)
|
||
|
|
#define MICROPY_HW_SPI5_MOSI (pin_E14)
|
||
|
|
|
||
|
|
// CAN busses
|
||
|
|
#define MICROPY_HW_CAN1_TX (pin_G1)
|
||
|
|
#define MICROPY_HW_CAN1_RX (pin_G0)
|
||
|
|
#define MICROPY_HW_CAN2_TX (pin_G12)
|
||
|
|
#define MICROPY_HW_CAN2_RX (pin_G11)
|
||
|
|
#define MICROPY_HW_CAN3_TX (pin_B4)
|
||
|
|
#define MICROPY_HW_CAN3_RX (pin_B3) // shared with UART1 or use pin_A8 shared with I2C3
|
||
|
|
|
||
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
||
|
|
#define MICROPY_HW_USRSW_PIN (pin_C13)
|
||
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
||
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
||
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
||
|
|
|
||
|
|
// LEDs
|
||
|
|
#define MICROPY_HW_LED1 (pin_B14) // red
|
||
|
|
#define MICROPY_HW_LED2 (pin_B0) // green
|
||
|
|
#define MICROPY_HW_LED3 (pin_B7) // blue
|
||
|
|
#define MICROPY_HW_LED1_PWM { TIM12, 12, TIM_CHANNEL_1, GPIO_AF9_TIM12 }
|
||
|
|
#define MICROPY_HW_LED2_PWM { TIM3, 3, TIM_CHANNEL_3, GPIO_AF2_TIM3 }
|
||
|
|
#define MICROPY_HW_LED3_PWM { TIM4, 4, TIM_CHANNEL_2, GPIO_AF2_TIM4 }
|
||
|
|
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
|
||
|
|
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
|
||
|
|
|
||
|
|
// USB config (CN13 - USB OTG FS)
|
||
|
|
#define MICROPY_HW_USB_FS (1)
|
||
|
|
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
|
||
|
|
#define MICROPY_HW_USB_OTG_ID_PIN (pin_A10)
|