nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
/*
|
|
|
|
|
* This file is part of the MicroPython project, http://micropython.org/
|
|
|
|
|
*
|
|
|
|
|
* The MIT License (MIT)
|
|
|
|
|
*
|
|
|
|
|
* Copyright (c) 2018 Glenn Ruben Bakke
|
|
|
|
|
* Copyright (c) 2018 Ayke van Laethem
|
|
|
|
|
*
|
|
|
|
|
* Permission is hereby granted, free of charge, to any person obtaining a copy
|
|
|
|
|
* of this software and associated documentation files (the "Software"), to deal
|
|
|
|
|
* in the Software without restriction, including without limitation the rights
|
|
|
|
|
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
|
|
|
|
* copies of the Software, and to permit persons to whom the Software is
|
|
|
|
|
* furnished to do so, subject to the following conditions:
|
|
|
|
|
*
|
|
|
|
|
* The above copyright notice and this permission notice shall be included in
|
|
|
|
|
* all copies or substantial portions of the Software.
|
|
|
|
|
*
|
|
|
|
|
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
|
|
|
|
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
|
|
|
|
|
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
|
|
|
|
|
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
|
|
|
|
|
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
|
|
|
|
|
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
|
|
|
|
|
* THE SOFTWARE.
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#ifndef NRFX_CONFIG_H
|
|
|
|
|
#define NRFX_CONFIG_H
|
|
|
|
|
|
2022-04-02 19:36:10 -04:00
|
|
|
#include "py/mpconfig.h"
|
2018-04-05 14:46:24 -04:00
|
|
|
#include "nrf.h"
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
|
|
|
|
|
// Port specific defines
|
|
|
|
|
#ifndef NRFX_LOG_ENABLED
|
|
|
|
|
#define NRFX_LOG_ENABLED 0
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#define NRFX_LOG_UART_DISABLED 1
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
// NRFX configurations
|
|
|
|
|
|
|
|
|
|
#if NRF51 || NRF52832
|
|
|
|
|
#define GPIO_COUNT 1
|
2018-04-02 18:10:05 -04:00
|
|
|
#elif NRF52840 || NRF52840_XXAA
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
#define GPIO_COUNT 2
|
2019-09-26 16:25:16 -04:00
|
|
|
#elif NRF9160_XXAA
|
|
|
|
|
#define GPIO_COUNT 1
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
#endif
|
|
|
|
|
|
2019-10-09 14:01:51 -04:00
|
|
|
#if defined(NRF52840)
|
|
|
|
|
// for tinyusb
|
2020-04-16 03:13:57 -04:00
|
|
|
// #define NRFX_IRQ_IS_ENABLED 1
|
2019-10-09 14:01:51 -04:00
|
|
|
#define NRFX_POWER_ENABLED 1
|
2020-03-25 02:01:38 -04:00
|
|
|
#define NRFX_POWER_DEFAULT_CONFIG_IRQ_PRIORITY 2
|
2019-10-09 14:01:51 -04:00
|
|
|
#define NRFX_SYSTICK_ENABLED 1
|
|
|
|
|
#endif
|
|
|
|
|
|
2018-04-02 18:10:05 -04:00
|
|
|
#define NRFX_GPIOTE_ENABLED 1
|
|
|
|
|
#define NRFX_GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS 1
|
|
|
|
|
#if NRF51
|
2020-03-25 02:01:38 -04:00
|
|
|
#define NRFX_GPIOTE_DEFAULT_CONFIG_IRQ_PRIORITY 3
|
2018-04-02 18:10:05 -04:00
|
|
|
#else
|
2020-03-25 02:01:38 -04:00
|
|
|
#define NRFX_GPIOTE_DEFAULT_CONFIG_IRQ_PRIORITY 6
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if defined(NRF51) || defined(NRF52_SERIES)
|
|
|
|
|
#define NRFX_TEMP_ENABLED 1
|
|
|
|
|
#if NRF51
|
|
|
|
|
#define NRFX_TEMP_DEFAULT_CONFIG_IRQ_PRIORITY 3
|
|
|
|
|
#else
|
|
|
|
|
#define NRFX_TEMP_DEFAULT_CONFIG_IRQ_PRIORITY 7
|
|
|
|
|
#endif
|
2018-04-02 18:10:05 -04:00
|
|
|
#endif
|
|
|
|
|
|
2019-09-26 16:25:16 -04:00
|
|
|
#if defined(NRF51) || defined(NRF52_SERIES)
|
|
|
|
|
#define NRFX_UART_ENABLED 1
|
|
|
|
|
#define NRFX_UART0_ENABLED 1
|
|
|
|
|
#define NRFX_UART1_ENABLED 1
|
|
|
|
|
#else
|
|
|
|
|
#define NRFX_UARTE_ENABLED 1
|
|
|
|
|
#define NRFX_UARTE0_ENABLED 1
|
|
|
|
|
#define NRFX_UARTE1_ENABLED 1
|
|
|
|
|
#define NRFX_UARTE2_ENABLED 1
|
|
|
|
|
#define NRFX_UARTE3_ENABLED 1
|
|
|
|
|
#endif
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
|
2019-09-26 16:25:16 -04:00
|
|
|
#if defined(NRF51) || defined(NRF52_SERIES)
|
|
|
|
|
#define NRFX_TWI_ENABLED (MICROPY_PY_MACHINE_I2C)
|
|
|
|
|
#define NRFX_TWI0_ENABLED 1
|
|
|
|
|
#define NRFX_TWI1_ENABLED 1
|
|
|
|
|
#elif defined(NRF9160_XXAA)
|
|
|
|
|
#define NRFX_TWIM_ENABLED (MICROPY_PY_MACHINE_I2C)
|
|
|
|
|
#define NRFX_TWIM0_ENABLED 1
|
|
|
|
|
#define NRFX_TWIM1_ENABLED 1
|
|
|
|
|
#endif
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
|
2018-05-08 14:31:15 -04:00
|
|
|
#if defined(NRF51) || defined(NRF52832)
|
|
|
|
|
#define NRFX_SPI_ENABLED (MICROPY_PY_MACHINE_HW_SPI)
|
|
|
|
|
#define NRFX_SPI0_ENABLED 1
|
|
|
|
|
#define NRFX_SPI1_ENABLED 1
|
|
|
|
|
|
|
|
|
|
#if defined(NRF52832)
|
|
|
|
|
#define NRFX_SPI2_ENABLED 1
|
|
|
|
|
#endif
|
|
|
|
|
#elif defined(NRF52840)
|
|
|
|
|
#define NRFX_SPIM_ENABLED (MICROPY_PY_MACHINE_HW_SPI)
|
|
|
|
|
#define NRFX_SPIM0_ENABLED 1
|
|
|
|
|
#define NRFX_SPIM1_ENABLED 1
|
|
|
|
|
#define NRFX_SPIM2_ENABLED 1
|
|
|
|
|
#define NRFX_SPIM3_ENABLED (NRF52840)
|
2019-09-26 16:25:16 -04:00
|
|
|
#elif defined(NRF9160_XXAA)
|
|
|
|
|
#define NRFX_SPIM_ENABLED (MICROPY_PY_MACHINE_HW_SPI)
|
|
|
|
|
#define NRFX_SPIM0_ENABLED 1
|
|
|
|
|
#define NRFX_SPIM1_ENABLED 1
|
|
|
|
|
|
2020-02-26 23:36:53 -05:00
|
|
|
// 0 NRF_GPIO_PIN_NOPULL
|
|
|
|
|
// 1 NRF_GPIO_PIN_PULLDOWN
|
|
|
|
|
// 3 NRF_GPIO_PIN_PULLUP
|
2019-09-26 16:25:16 -04:00
|
|
|
#define NRFX_SPIM_MISO_PULL_CFG 1
|
2018-04-05 14:46:24 -04:00
|
|
|
#endif // NRF51
|
|
|
|
|
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
// 0 NRF_GPIO_PIN_NOPULL
|
|
|
|
|
// 1 NRF_GPIO_PIN_PULLDOWN
|
|
|
|
|
// 3 NRF_GPIO_PIN_PULLUP
|
|
|
|
|
#define NRFX_SPI_MISO_PULL_CFG 1
|
2018-04-05 14:46:24 -04:00
|
|
|
#define NRFX_SPIM_MISO_PULL_CFG 1
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
|
|
|
|
|
#define NRFX_RTC_ENABLED (MICROPY_PY_MACHINE_RTCOUNTER)
|
|
|
|
|
#define NRFX_RTC0_ENABLED 1
|
|
|
|
|
#define NRFX_RTC1_ENABLED 1
|
2020-07-09 14:41:11 -04:00
|
|
|
#define NRFX_RTC2_ENABLED (!NRF51) && (!NRF9160_XXAA)
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
|
|
|
|
|
#define NRFX_TIMER_ENABLED (MICROPY_PY_MACHINE_TIMER)
|
|
|
|
|
#define NRFX_TIMER0_ENABLED 1
|
|
|
|
|
#define NRFX_TIMER1_ENABLED (!MICROPY_PY_MACHINE_SOFT_PWM)
|
|
|
|
|
#define NRFX_TIMER2_ENABLED 1
|
2019-09-26 16:25:16 -04:00
|
|
|
#define NRFX_TIMER3_ENABLED (!NRF51) && (!NRF9160_XXAA)
|
|
|
|
|
#define NRFX_TIMER4_ENABLED (!NRF51) && (!NRF9160_XXAA)
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
|
|
|
|
|
|
|
|
|
|
#define NRFX_PWM_ENABLED (!NRF51) && MICROPY_PY_MACHINE_HW_PWM
|
|
|
|
|
#define NRFX_PWM0_ENABLED 1
|
|
|
|
|
#define NRFX_PWM1_ENABLED 1
|
|
|
|
|
#define NRFX_PWM2_ENABLED 1
|
|
|
|
|
#define NRFX_PWM3_ENABLED (NRF52840)
|
|
|
|
|
|
2019-04-03 17:51:38 -04:00
|
|
|
#define NRFX_NVMC_ENABLED 1
|
|
|
|
|
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
// Peripheral Resource Sharing
|
2018-05-08 14:31:15 -04:00
|
|
|
#if defined(NRF51) || defined(NRF52832)
|
|
|
|
|
#define NRFX_PRS_BOX_0_ENABLED (NRFX_TWI_ENABLED && NRFX_TWI0_ENABLED && NRFX_SPI_ENABLED && NRFX_SPI0_ENABLED)
|
|
|
|
|
#define NRFX_PRS_BOX_1_ENABLED (NRFX_TWI_ENABLED && NRFX_TWI1_ENABLED && NRFX_SPI_ENABLED && NRFX_SPI1_ENABLED)
|
|
|
|
|
|
|
|
|
|
#if defined(NRF52832)
|
|
|
|
|
#define NRFX_PRS_BOX_2_ENABLED (NRFX_TWI_ENABLED && NRFX_TWI1_ENABLED && NRFX_SPI_ENABLED && NRFX_SPI1_ENABLED)
|
|
|
|
|
#endif
|
|
|
|
|
#elif defined(NRF52840)
|
|
|
|
|
#define NRFX_PRS_BOX_0_ENABLED (NRFX_TWI_ENABLED && NRFX_TWI0_ENABLED && NRFX_SPIM_ENABLED && NRFX_SPIM0_ENABLED)
|
|
|
|
|
#define NRFX_PRS_BOX_1_ENABLED (NRFX_TWI_ENABLED && NRFX_TWI1_ENABLED && NRFX_SPIM_ENABLED && NRFX_SPIM1_ENABLED)
|
|
|
|
|
#define NRFX_PRS_BOX_2_ENABLED (NRFX_TWI_ENABLED && NRFX_TWI2_ENABLED && NRFX_SPIM_ENABLED && NRFX_SPIM2_ENABLED)
|
2019-09-26 16:25:16 -04:00
|
|
|
#elif defined(NRF9160_XXAA)
|
|
|
|
|
#define NRFX_PRS_BOX_0_ENABLED (NRFX_TWIM_ENABLED && NRFX_TWIM0_ENABLED && NRFX_SPIM_ENABLED && NRFX_SPIM0_ENABLED)
|
|
|
|
|
#define NRFX_PRS_BOX_1_ENABLED (NRFX_TWIM_ENABLED && NRFX_TWIM1_ENABLED && NRFX_SPIM_ENABLED && NRFX_SPIM1_ENABLED)
|
|
|
|
|
#define NRFX_PRS_BOX_2_ENABLED (NRFX_TWIM_ENABLED && NRFX_TWIM2_ENABLED && NRFX_SPIM_ENABLED && NRFX_SPIM2_ENABLED)
|
2018-04-05 14:46:24 -04:00
|
|
|
#endif
|
2018-05-08 14:31:15 -04:00
|
|
|
|
|
|
|
|
#define NRFX_PRS_ENABLED (NRFX_PRS_BOX_0_ENABLED || NRFX_PRS_BOX_1_ENABLED || NRFX_PRS_BOX_2_ENABLED)
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
|
|
|
|
|
#define NRFX_SAADC_ENABLED !(NRF51) && (MICROPY_PY_MACHINE_ADC)
|
|
|
|
|
#define NRFX_ADC_ENABLED (NRF51) && (MICROPY_PY_MACHINE_ADC)
|
|
|
|
|
|
2019-09-26 16:25:16 -04:00
|
|
|
#if defined(NRF9160_XXAA)
|
|
|
|
|
|
|
|
|
|
#define NRF_CLOCK NRF_CLOCK_NS
|
|
|
|
|
#define NRF_DPPIC NRF_DPPIC_NS
|
|
|
|
|
#define NRF_EGU0 NRF_EGU0_NS
|
|
|
|
|
#define NRF_EGU1 NRF_EGU1_NS
|
|
|
|
|
#define NRF_EGU2 NRF_EGU2_NS
|
|
|
|
|
#define NRF_EGU3 NRF_EGU3_NS
|
|
|
|
|
#define NRF_EGU4 NRF_EGU4_NS
|
|
|
|
|
#define NRF_EGU5 NRF_EGU5_NS
|
|
|
|
|
#define NRF_FPU NRF_FPU_NS
|
|
|
|
|
#define NRF_P0 NRF_P0_NS
|
|
|
|
|
#define NRF_I2S NRF_I2S_NS
|
|
|
|
|
#define NRF_KMU NRF_KMU_NS
|
|
|
|
|
#define NRF_NVMC NRF_NVMC_NS
|
|
|
|
|
#define NRF_PDM NRF_PDM_NS
|
|
|
|
|
#define NRF_POWER NRF_POWER_NS
|
|
|
|
|
#define NRF_PWM0 NRF_PWM0_NS
|
|
|
|
|
#define NRF_PWM1 NRF_PWM1_NS
|
|
|
|
|
#define NRF_PWM2 NRF_PWM2_NS
|
|
|
|
|
#define NRF_PWM3 NRF_PWM3_NS
|
|
|
|
|
#define NRF_REGULATORS NRF_REGULATORS_NS
|
|
|
|
|
#define NRF_RTC0 NRF_RTC0_NS
|
|
|
|
|
#define NRF_RTC1 NRF_RTC1_NS
|
|
|
|
|
#define NRF_SAADC NRF_SAADC_NS
|
|
|
|
|
#define NRF_SPIM0 NRF_SPIM0_NS
|
|
|
|
|
#define NRF_SPIM1 NRF_SPIM1_NS
|
|
|
|
|
#define NRF_SPIM2 NRF_SPIM2_NS
|
|
|
|
|
#define NRF_SPIM3 NRF_SPIM3_NS
|
|
|
|
|
#define NRF_SPIS0 NRF_SPIS0_NS
|
|
|
|
|
#define NRF_SPIS1 NRF_SPIS1_NS
|
|
|
|
|
#define NRF_SPIS2 NRF_SPIS2_NS
|
|
|
|
|
#define NRF_SPIS3 NRF_SPIS3_NS
|
|
|
|
|
#define NRF_TIMER0 NRF_TIMER0_NS
|
|
|
|
|
#define NRF_TIMER1 NRF_TIMER1_NS
|
|
|
|
|
#define NRF_TIMER2 NRF_TIMER2_NS
|
|
|
|
|
#define NRF_TWIM0 NRF_TWIM0_NS
|
|
|
|
|
#define NRF_TWIM1 NRF_TWIM1_NS
|
|
|
|
|
#define NRF_TWIM2 NRF_TWIM2_NS
|
|
|
|
|
#define NRF_TWIM3 NRF_TWIM3_NS
|
|
|
|
|
#define NRF_TWIS0 NRF_TWIS0_NS
|
|
|
|
|
#define NRF_TWIS1 NRF_TWIS1_NS
|
|
|
|
|
#define NRF_TWIS2 NRF_TWIS2_NS
|
|
|
|
|
#define NRF_TWIS3 NRF_TWIS3_NS
|
|
|
|
|
#define NRF_UARTE0 NRF_UARTE0_NS
|
|
|
|
|
#define NRF_UARTE1 NRF_UARTE1_NS
|
|
|
|
|
#define NRF_UARTE2 NRF_UARTE2_NS
|
|
|
|
|
#define NRF_UARTE3 NRF_UARTE3_NS
|
|
|
|
|
#define NRF_VMC NRF_VMC_NS
|
|
|
|
|
#define NRF_WDT NRF_WDT_NS
|
|
|
|
|
#define NRF_IPC NRF_IPC_NS
|
|
|
|
|
|
|
|
|
|
#define NRF_CRYPTOCELL NRF_CRYPTOCELL_S
|
|
|
|
|
#define NRF_FICR NRF_FICR_S
|
|
|
|
|
#define NRF_GPIOTE0 NRF_GPIOTE0_S
|
|
|
|
|
#define NRF_GPIOTE1 NRF_GPIOTE1_NS
|
|
|
|
|
#define NRF_SPU NRF_SPU_S
|
|
|
|
|
#define NRF_UICR NRF_UICR_S
|
|
|
|
|
|
|
|
|
|
#define NRF_GPIOTE NRF_GPIOTE1_NS
|
|
|
|
|
#define GPIOTE_IRQn GPIOTE1_IRQn
|
|
|
|
|
#define GPIOTE_IRQHandler GPIOTE1_IRQHandler
|
|
|
|
|
|
|
|
|
|
#endif
|
|
|
|
|
|
nrf: Replace custom-HAL with nrfx-HAL
Summarized this squashed PR replaces the hal/ folder in the port. This has been replaced the official
HAL layer from Nordic Semiconductor; https://github.com/NordicSemiconductor/nrfx.
A Git submodule has been added under lib/nrfx, for the nrfx dependency.
The drivers / modules has been updated to use this new HAL layer; nrfx at v1.0.0.
Also, header files and system files for nrf51/nrf52x chip variants has been deleted from the device/ folder, only keeping back the startup files written in C. All other files are now fetched from nrfx.
3 new header files in the ports/nrf/ folder has been added to configure nrfx (nrfx_config.h), logging (nrfx_log.h) and glue nrfx together with the drivers and modules from micropython (nrfx_glue.h).
The PR has been a joint effort from @aykevl (Ayke van Laethem) and @glennrub.
For reference, the commit log will be kept to get an overview of the changes done:
* ports/nrf: Initial commit for moving hal to Nordic Semiconductor BSD-3 licensed nrfx-hal.
* ports/nrf: Adding nrfx, Nordic Semiconductor BSD-3 hal layer, as git submodule checked out at lib/nrfx.
* ports/nrf/modules/machine/uart: Fixing bug which set hwfc to parity excluded, always resulting in no flow control, hence corrupted output. Also adding an extra loop on uart_tx_char to prevent any tx when any ongoing tx is in progress.
* ports/nrf/i2c: Moving I2C over to nrfx driver.
* ports/nrf/modules/machine/i2c: Alignment. Renaming print function param 'o' to 'self_in'
* ports/nrf/spi: Updating SPI machine module to use nrfx drivers.
* ports/nrf: Renaming modules/machine/rtc.c/.h to rtcounter.c/.h to not confuse the peripheral with Real-Time Clock:
* ports/nrf: Updating various files after renaming machine module RTC to RTCounter.
* ports/nrf: Renaming RTC to RTCounter in modmachine globals dict table. Also updating object type name to reflect new module name.
* ports/nrf: Fixing leftovers after renaming rtc to rtcounter.
* ports/nrf: Early untested adoption of nrfx_rtc in RTCounter. Untested.
* nrf/modules/machine/i2c: Improve keyword argument handling
* ports/nrf/modules/temp: Updating Temp machine module to use nrfx defined hal nrf_temp.h. Moving logic of BLE stack awareness to machine module.
* ports/nrf/boards/pca10040: Enable machine Temp module.
* nrf/modules/machine/rtcounter: Remove magic constants.
* ports/nrf: Adding base support for nrfx module logging. Adding option to disable logging of UART as it might log its own setup over UART while the peripheral is not yet set up. Logging of UART could make sense if other transport of log is used.
* ports/nrf: updating nrfx_log.h with more correct parenthisis on macro grouping.
* ports/nrf: Updating nrfx logging with configuration to disable logging of UART module. The pattern can be used to turn off other modules as well. However, for now UART is the only module locking itself by logging before the peripheral is configured. Logging is turned off by default, can be enabled in nrfx_config.h by setting NRFX_LOG_ENABLED=1.
* ports/nrf/modules/random: Updating modrandom to use nrfx hal for rng. Not using nrfx-driver for this peripheral as its blocking mode would do the trick on RNG. Moving softdevice aware code from legacy hal to modrandom.c.
* nrf: Enable Peripheral Resource Sharing.
This enables TWI and SPI to be enabled at the same time.
* nrf/Makefile: Define MCU sub variant (e.g. NRF51822/NRF51422)
* nrf: Port TIMER peripheral to nrfx HAL.
* nrf/modules/machine/uart: Optimize UART module
For a nRF51, this results in a size reduction of:
.text: -68 bytes
.data: -56 bytes
* nrf/modules/machine/uart: Don't use magic index numbers.
* nrf/modules/machine/uart: Fix off-by-one error.
For nrf51:
.text: -40 bytes
* nrf/modules/machine/rtcounter: Update for nrfx HAL.
* nrf/modules/machine/i2c: Reduce RAM consumption.
Reductions for the nrf51:
flash: -108 bytes
RAM: -72 bytes
* nrf/mpconfigport: Avoid unnecessary root pointers.
This saves 92 bytes of RAM.
* nrf: Support SoftDevice with nrfx HAL.
* nrf: Add NVMC peripheral (microbitfs) support.
There is no support yet for a SoftDevice.
It also fixes a potentially serious bug in start_index generation.
* nrf/modules/machine/spi: Optimize SPI peripheral.
nrf51:
text: -340 bytes
data: -72 bytes
nrf52:
text: -352 bytes
data: -108 bytes
* nrf/modules/random: Forgot to commit header file.
* nrf: Make nrfx_config.h universal for all boards.
* nrf: Use SoftDevice API for flash access when built for SD
* nrf/drivers/bluetooth: Remove legacy HAL driver includes.
These were not used anymore so can be removed.
* ports/nrf/microbit: Port microbit targets to nrfx HAL
Initial port of microbit modules to use nrfx HAL layer.
Tested display/image and modmusic on micro:bit to verify that
softpwm and ticker for nrf51 is working as expected.
Changing IRQ priority on timer to priority 2, as 1 might collide if
used side by side of SD110 BLE stack.
The patch reserves Timer1 peripheral compile time. This is not ideal
and should be resolved in seperate task.
* nrf/boards/microbit: Remove custom nrfx_config.h from microbit target, adding disablement of timer1 if softpwm is enabled.
* nrf/adc: Update ADC module to use nrfx
* nrf/modules/machine/pwm: Updating machine PWM module to use nrfx HAL driver.
examples/nrf52_pwm.py and examples/nrf52_servo.py tested on pca10040.
* nrf: Removing hal folder and boards nrf5x_hal_conf.h headers.
* nrf/nrfx_glue: Adding direct NVIC access for S110 BLE stack
If SoftDevice s110 has not yet been initialized, the IRQ will not be forwarded to
the application using the sd_nvic* function calls. Hence, direct access to cmsi
nvic functions are used instead if SoftDevice is not enabled.
* nrf/drivers/ticker: Setting IRQ priority 3 on Timer1
SoftDevice fails to initilize if Timer1 has been configured to priority
level 2 before enabling the SD. The timer is set to priority 1, higher than BLE
stack in order to provide better quality of music rendering when used with the
music module. This might be too high, time will show.
* nrf/examples: Updating ubluepy_temp after moving RTCounter to nrfx.
* nrf: delete duplicate files from device folder which can be located in nrfx/mdk.
* nrf/Makefile: Fetch system files from nrfx.
Testing on each device sub-variant to figure out which system file to
use. Reason for this is that nrf52.c is actually defining nrf52832.
Removing NRF_DEFINES parameter setting the device in use into the
same sub-variant test, as NRF52 is unique to nrf52832 when using nrfx.
Without this exclusion of -DNRF52 in compilation for nrf52840, the
device will be interpreted as a nrf52, hence nrf52832.
Also, changing name on variable SRC_NRF_HAL to SRC_NRFX_HAL to
explicitly tell the origin of the file.
* nrf: Updating device #ifdefs to be more open to non-nrf51 targets.
* nrf/modules/machine/uart: Removing second instance of UART for nrf52840 as it only has one non-DMA variant.
* nrf/device: Removing system files as these are now used from nrfx/mdk
* nrf: Moving startup files in device one level up as there is no need for deep hierarchy.
* nrf: Use NRF52_SERIES defined in nrfx/mdk/nrf.h as define value when testing for both nrf52(832) and nrf52840 variants.
* nrf/modules/machine/uart: Enable UART RX by default
Enable rx by default after intiialization of the peripheral.
Else, the nrfx driver will re-enable rx for each byte read
on uart REPL, clearing the EVENT_RXDRDY before second byte,
which again will make second byte get lost and read will get stuck.
This happens if the bytes are transmitted nrf(51) while still
processing the previous byte. Not seen on nrf52, but should
also become an issue at higher speeds.
This patch sets rx to always be enabled. Hence, not clearing the event
between read bytes, and it will be able to detect next byte recieved
upon finishing the first.
* nrf/modules/machine/timer: Fixing defines excluding Timer1 if ticker/softpwm is used.
* nrf: Switching import form mpconfigboard.h to mpconfigport.h in nrfx_config.h as mpconfigboard.h might define default values for defines not set by board specific header.
* nrf/modules/machine/i2c: nrfx integration fixes
Increasing speed to 400K.
Returning Address NACK's as MP error code; MP_ENODEV.
Returning MP_ETIMEOUT on all other error codes from TWI nrfx driver
except the ANACK.
Enabling and disabling the TWI peripheral before and after each transaction.
* nrf/examples: Updating ssd1306_mod.py to split framebuffer transfer into multiple chunks
* nrf/modules/machine/i2c: Return MP_EIO error if Data NACK occurs.
* nrf: Addressing review comments.
* nrf: Updating git submodule and users to nrfx v1.0.0.
* nrf/modules/machine/adc: Update adc module to follow v1.0.0 nrfx API.
* nrf/modules/machine/spi: Implement init and deinit functions
Extending SPI objects with a config member such that
configuration can be kept between new() and init().
Moving initialization done in new() to common init
function shared between the module functions.
If SPI is already configured, the SPI peripheral will
be uninitialized before initalized again.
Adding logic to handle initialization of polarity and
phase. As well, updating default speed to 1M from 500K.
* nrf/modules/machine: Removing unused nrfx includes in machine module header files
2018-03-27 18:35:14 -04:00
|
|
|
#endif // NRFX_CONFIG_H
|
