circuitpython/ports/atmel-samd/boards/arduino_mkr1300/mpconfigboard.h

#define MICROPY_HW_BOARD_NAME "Arduino MKR1300"
#define MICROPY_HW_MCU_NAME "samd21g18"

#define MICROPY_PORT_A        (0)
#define MICROPY_PORT_B        (0)
#define MICROPY_PORT_C        (0)

#define MICROPY_HW_LED_STATUS   (&pin_PB23)

#define CIRCUITPY_INTERNAL_NVM_SIZE 256

#define BOARD_FLASH_SIZE (0x00040000 - 0x2000 - 0x010000 - CIRCUITPY_INTERNAL_NVM_SIZE)

#define DEFAULT_I2C_BUS_SCL (&pin_PA09)
#define DEFAULT_I2C_BUS_SDA (&pin_PA08)

#define DEFAULT_SPI_BUS_SCK (&pin_PA13)
#define DEFAULT_SPI_BUS_MOSI (&pin_PA12)
#define DEFAULT_SPI_BUS_MISO (&pin_PA15)

#define DEFAULT_UART_BUS_RX (&pin_PB23)
#define DEFAULT_UART_BUS_TX (&pin_PB22)

// USB is always used internally so skip the pin objects for it.
#define IGNORE_PIN_PA24     1
#define IGNORE_PIN_PA25     1
Add Arduino MKR1300 2018-10-22 20:38:24 -04:00			`#define MICROPY_HW_BOARD_NAME "Arduino MKR1300"`
			`#define MICROPY_HW_MCU_NAME "samd21g18"`

Update MKR1300 board definition too 2018-11-09 03:49:02 -05:00			`#define MICROPY_PORT_A (0)`
Add Arduino MKR1300 2018-10-22 20:38:24 -04:00			`#define MICROPY_PORT_B (0)`
			`#define MICROPY_PORT_C (0)`

Rework safe mode and have heap overwrite trigger it. This creates a common safe mode mechanic that ports can share. As a result, the nRF52 now has safe mode support as well. The common safe mode adds a 700ms delay at startup where a reset during that window will cause a reset into safe mode. This window is designated by a yellow status pixel and flashing the single led three times. A couple NeoPixel fixes are included for the nRF52 as well. Fixes #1034. Fixes #990. Fixes #615. 2018-12-06 17:24:20 -05:00			`#define MICROPY_HW_LED_STATUS (&pin_PB23)`

Enable 256b of nvm storage for all samd21x18-bootloader.ld boards. 2019-03-24 12:02:07 -04:00			`#define CIRCUITPY_INTERNAL_NVM_SIZE 256`
Add Arduino MKR1300 2018-10-22 20:38:24 -04:00
Enable 256b of nvm storage for all samd21x18-bootloader.ld boards. 2019-03-24 12:02:07 -04:00			`#define BOARD_FLASH_SIZE (0x00040000 - 0x2000 - 0x010000 - CIRCUITPY_INTERNAL_NVM_SIZE)`
Add Arduino MKR1300 2018-10-22 20:38:24 -04:00
			`#define DEFAULT_I2C_BUS_SCL (&pin_PA09)`
			`#define DEFAULT_I2C_BUS_SDA (&pin_PA08)`

			`#define DEFAULT_SPI_BUS_SCK (&pin_PA13)`
			`#define DEFAULT_SPI_BUS_MOSI (&pin_PA12)`
			`#define DEFAULT_SPI_BUS_MISO (&pin_PA15)`

			`#define DEFAULT_UART_BUS_RX (&pin_PB23)`
			`#define DEFAULT_UART_BUS_TX (&pin_PB22)`

			`// USB is always used internally so skip the pin objects for it.`
			`#define IGNORE_PIN_PA24 1`
			`#define IGNORE_PIN_PA25 1`