circuitpython/ports/stm32/boards/MIKROE_CLICKER2_STM32/mpconfigboard.h

Ignoring revisions in .git-blame-ignore-revs. Click here to bypass and see the normal blame view.

87 lines
3.1 KiB
C
Raw Normal View History

#define MICROPY_HW_BOARD_NAME "MIKROE_CLICKER2_STM32"
#define MICROPY_HW_MCU_NAME "STM32F407"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_DAC (1)
#define MICROPY_HW_ENABLE_USB (1)
// HSE is 25MHz
#define MICROPY_HW_CLK_PLLM (25)
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (7)
#define MICROPY_HW_CLK_LAST_FREQ (1)
// The board has a 32kHz crystal for the RTC
#define MICROPY_HW_RTC_USE_LSE (1)
#define MICROPY_HW_RTC_USE_US (0)
#define MICROPY_HW_RTC_USE_CALOUT (0) // turn on/off PC13 512Hz output
// UART config
// mikroBUS slot 1
#define MICROPY_HW_UART2_NAME "SLOT1"
#define MICROPY_HW_UART2_TX (pin_D5)
#define MICROPY_HW_UART2_RX (pin_D6)
// mikroBUS slot 2
#define MICROPY_HW_UART3_NAME "SLOT2"
#define MICROPY_HW_UART3_TX (pin_D8)
#define MICROPY_HW_UART3_RX (pin_D9)
// HDR2
#define MICROPY_HW_UART4_NAME "HDR2"
#define MICROPY_HW_UART4_TX (pin_A0)
#define MICROPY_HW_UART4_RX (pin_A1)
// I2C buses
// mikroBUS slot 2 / HDR2
#define MICROPY_HW_I2C2_NAME "SLOT2"
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
// mikroBUS slot 1
#define MICROPY_HW_I2C3_NAME "SLOT1"
#define MICROPY_HW_I2C3_SCL (pin_A8)
#define MICROPY_HW_I2C3_SDA (pin_C9)
// SPI buses
// mikroBUS slot 2 / HDR1
#define MICROPY_HW_SPI2_NAME "SLOT2"
#define MICROPY_HW_SPI2_NSS (pin_E11)
#define MICROPY_HW_SPI2_SCK (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)
// mikroBUS slot 1
#define MICROPY_HW_SPI3_NAME "SLOT1"
#define MICROPY_HW_SPI3_NSS (pin_E8)
#define MICROPY_HW_SPI3_SCK (pin_C10)
#define MICROPY_HW_SPI3_MISO (pin_C11)
#define MICROPY_HW_SPI3_MOSI (pin_C12)
// USRSW is pulled high; pressing the button makes the input go low
#define MICROPY_HW_USRSW_PIN (pin_E0)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
#define MICROPY_HW_USRSW_PRESSED (0)
// LEDs
#define MICROPY_HW_LED1 (pin_E12) // red
#define MICROPY_HW_LED2 (pin_E15) // red
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))
// USB config
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
// Bootloader configuration (only needed if Mboot is used)
#define MBOOT_I2C_PERIPH_ID 2
#define MBOOT_I2C_SCL (pin_B10)
#define MBOOT_I2C_SDA (pin_B11)
#define MBOOT_I2C_ALTFUNC (4)
#define MBOOT_BOOTPIN_PIN (pin_A10)
#define MBOOT_BOOTPIN_PULL (MP_HAL_PIN_PULL_NONE)
#define MBOOT_BOOTPIN_ACTIVE (0)
#define MBOOT_FSLOAD (1)
#define MBOOT_VFS_FAT (1)