djsundog/circuitpython
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
439ff90959
circuitpython/stm/lib/stm32f4xx_pwr.c

680 lines
26 KiB
C
Raw Normal View History

Add support for RTC, used as a calendar.
2013-10-25 21:06:37 -04:00
/**
******************************************************************************
* @file stm32f4xx_pwr.c
* @author MCD Application Team
* @version V1.1.0
* @date 11-January-2013
* @brief This file provides firmware functions to manage the following
* functionalities of the Power Controller (PWR) peripheral:
* + Backup Domain Access
* + PVD configuration
* + WakeUp pin configuration
* + Main and Backup Regulators configuration
* + FLASH Power Down configuration
* + Low Power modes configuration
* + Flags management
*
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT 2013 STMicroelectronics</center></h2>
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_conf.h"
#include "stm32f4xx_pwr.h"
#include "stm32f4xx_rcc.h"
/** @addtogroup STM32F4xx_StdPeriph_Driver
* @{
*/
/** @defgroup PWR
* @brief PWR driver modules
* @{
*/
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* --------- PWR registers bit address in the alias region ---------- */
#define PWR_OFFSET (PWR_BASE - PERIPH_BASE)
/* --- CR Register ---*/
/* Alias word address of DBP bit */
#define CR_OFFSET (PWR_OFFSET + 0x00)
#define DBP_BitNumber 0x08
#define CR_DBP_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (DBP_BitNumber * 4))
/* Alias word address of PVDE bit */
#define PVDE_BitNumber 0x04
#define CR_PVDE_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (PVDE_BitNumber * 4))
/* Alias word address of FPDS bit */
#define FPDS_BitNumber 0x09
#define CR_FPDS_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (FPDS_BitNumber * 4))
/* Alias word address of PMODE bit */
#define PMODE_BitNumber 0x0E
#define CR_PMODE_BB (PERIPH_BB_BASE + (CR_OFFSET * 32) + (PMODE_BitNumber * 4))
/* --- CSR Register ---*/
/* Alias word address of EWUP bit */
#define CSR_OFFSET (PWR_OFFSET + 0x04)
#define EWUP_BitNumber 0x08
#define CSR_EWUP_BB (PERIPH_BB_BASE + (CSR_OFFSET * 32) + (EWUP_BitNumber * 4))
/* Alias word address of BRE bit */
#define BRE_BitNumber 0x09
#define CSR_BRE_BB (PERIPH_BB_BASE + (CSR_OFFSET * 32) + (BRE_BitNumber * 4))
/* ------------------ PWR registers bit mask ------------------------ */
/* CR register bit mask */
#define CR_DS_MASK ((uint32_t)0xFFFFFFFC)
#define CR_PLS_MASK ((uint32_t)0xFFFFFF1F)
#define CR_VOS_MASK ((uint32_t)0xFFFF3FFF)
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup PWR_Private_Functions
* @{
*/
/** @defgroup PWR_Group1 Backup Domain Access function
* @brief Backup Domain Access function
*
@verbatim
===============================================================================
##### Backup Domain Access function #####
===============================================================================
[..]
After reset, the backup domain (RTC registers, RTC backup data
registers and backup SRAM) is protected against possible unwanted
write accesses.
To enable access to the RTC Domain and RTC registers, proceed as follows:
(+) Enable the Power Controller (PWR) APB1 interface clock using the
RCC_APB1PeriphClockCmd() function.
(+) Enable access to RTC domain using the PWR_BackupAccessCmd() function.
@endverbatim
* @{
*/
/**
* @brief Deinitializes the PWR peripheral registers to their default reset values.
* @param None
* @retval None
*/
void PWR_DeInit(void)
{
RCC_APB1PeriphResetCmd(RCC_APB1Periph_PWR, ENABLE);
RCC_APB1PeriphResetCmd(RCC_APB1Periph_PWR, DISABLE);
}
/**
* @brief Enables or disables access to the backup domain (RTC registers, RTC
* backup data registers and backup SRAM).
* @note If the HSE divided by 2, 3, ..31 is used as the RTC clock, the
* Backup Domain Access should be kept enabled.
* @param NewState: new state of the access to the backup domain.
* This parameter can be: ENABLE or DISABLE.
* @retval None
*/
void PWR_BackupAccessCmd(FunctionalState NewState)
{
/* Check the parameters */
assert_param(IS_FUNCTIONAL_STATE(NewState));
*(__IO uint32_t *) CR_DBP_BB = (uint32_t)NewState;
}
/**
* @}
*/
/** @defgroup PWR_Group2 PVD configuration functions
* @brief PVD configuration functions
*
@verbatim
===============================================================================
##### PVD configuration functions #####
===============================================================================
[..]
(+) The PVD is used to monitor the VDD power supply by comparing it to a
threshold selected by the PVD Level (PLS[2:0] bits in the PWR_CR).
(+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower
than the PVD threshold. This event is internally connected to the EXTI
line16 and can generate an interrupt if enabled through the EXTI registers.
(+) The PVD is stopped in Standby mode.
@endverbatim
* @{
*/
/**
* @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD).
* @param PWR_PVDLevel: specifies the PVD detection level
* This parameter can be one of the following values:
* @arg PWR_PVDLevel_0
* @arg PWR_PVDLevel_1
* @arg PWR_PVDLevel_2
* @arg PWR_PVDLevel_3
* @arg PWR_PVDLevel_4
* @arg PWR_PVDLevel_5
* @arg PWR_PVDLevel_6
* @arg PWR_PVDLevel_7
* @note Refer to the electrical characteristics of your device datasheet for
* more details about the voltage threshold corresponding to each
* detection level.
* @retval None
*/
void PWR_PVDLevelConfig(uint32_t PWR_PVDLevel)
{
uint32_t tmpreg = 0;
/* Check the parameters */
assert_param(IS_PWR_PVD_LEVEL(PWR_PVDLevel));
tmpreg = PWR->CR;
/* Clear PLS[7:5] bits */
tmpreg &= CR_PLS_MASK;
/* Set PLS[7:5] bits according to PWR_PVDLevel value */
tmpreg |= PWR_PVDLevel;
/* Store the new value */
PWR->CR = tmpreg;
}
/**
* @brief Enables or disables the Power Voltage Detector(PVD).
* @param NewState: new state of the PVD.
* This parameter can be: ENABLE or DISABLE.
* @retval None
*/
void PWR_PVDCmd(FunctionalState NewState)
{
/* Check the parameters */
assert_param(IS_FUNCTIONAL_STATE(NewState));
*(__IO uint32_t *) CR_PVDE_BB = (uint32_t)NewState;
}
/**
* @}
*/
/** @defgroup PWR_Group3 WakeUp pin configuration functions
* @brief WakeUp pin configuration functions
*
@verbatim
===============================================================================
##### WakeUp pin configuration functions #####
===============================================================================
[..]
(+) WakeUp pin is used to wakeup the system from Standby mode. This pin is
forced in input pull down configuration and is active on rising edges.
(+) There is only one WakeUp pin: WakeUp Pin 1 on PA.00.
@endverbatim
* @{
*/
/**
* @brief Enables or disables the WakeUp Pin functionality.
* @param NewState: new state of the WakeUp Pin functionality.
* This parameter can be: ENABLE or DISABLE.
* @retval None
*/
void PWR_WakeUpPinCmd(FunctionalState NewState)
{
/* Check the parameters */
assert_param(IS_FUNCTIONAL_STATE(NewState));
*(__IO uint32_t *) CSR_EWUP_BB = (uint32_t)NewState;
}
/**
* @}
*/
/** @defgroup PWR_Group4 Main and Backup Regulators configuration functions
* @brief Main and Backup Regulators configuration functions
*
@verbatim
===============================================================================
##### Main and Backup Regulators configuration functions #####
===============================================================================
[..]
(+) The backup domain includes 4 Kbytes of backup SRAM accessible only from
the CPU, and address in 32-bit, 16-bit or 8-bit mode. Its content is
retained even in Standby or VBAT mode when the low power backup regulator
is enabled. It can be considered as an internal EEPROM when VBAT is
always present. You can use the PWR_BackupRegulatorCmd() function to
enable the low power backup regulator and use the PWR_GetFlagStatus
(PWR_FLAG_BRR) to check if it is ready or not.
(+) When the backup domain is supplied by VDD (analog switch connected to VDD)
the backup SRAM is powered from VDD which replaces the VBAT power supply to
save battery life.
(+) The backup SRAM is not mass erased by an tamper event. It is read
protected to prevent confidential data, such as cryptographic private
key, from being accessed. The backup SRAM can be erased only through
the Flash interface when a protection level change from level 1 to
level 0 is requested.
-@- Refer to the description of Read protection (RDP) in the Flash
programming manual.
(+) The main internal regulator can be configured to have a tradeoff between
performance and power consumption when the device does not operate at
the maximum frequency. This is done through PWR_MainRegulatorModeConfig()
function which configure VOS bit in PWR_CR register:
(++) When this bit is set (Regulator voltage output Scale 1 mode selected)
the System frequency can go up to 168 MHz.
(++) When this bit is reset (Regulator voltage output Scale 2 mode selected)
the System frequency can go up to 144 MHz.
Refer to the datasheets for more details.
@endverbatim
* @{
*/
/**
* @brief Enables or disables the Backup Regulator.
* @param NewState: new state of the Backup Regulator.
* This parameter can be: ENABLE or DISABLE.
* @retval None
*/
void PWR_BackupRegulatorCmd(FunctionalState NewState)
{
/* Check the parameters */
assert_param(IS_FUNCTIONAL_STATE(NewState));
*(__IO uint32_t *) CSR_BRE_BB = (uint32_t)NewState;
}
/**
* @brief Configures the main internal regulator output voltage.
* @param PWR_Regulator_Voltage: specifies the regulator output voltage to achieve
* a tradeoff between performance and power consumption when the device does
* not operate at the maximum frequency (refer to the datasheets for more details).
* This parameter can be one of the following values:
* @arg PWR_Regulator_Voltage_Scale1: Regulator voltage output Scale 1 mode,
* System frequency up to 168 MHz.
* @arg PWR_Regulator_Voltage_Scale2: Regulator voltage output Scale 2 mode,
* System frequency up to 144 MHz.
* @arg PWR_Regulator_Voltage_Scale3: Regulator voltage output Scale 3 mode,
* System frequency up to 120 MHz
* @retval None
*/
void PWR_MainRegulatorModeConfig(uint32_t PWR_Regulator_Voltage)
{
uint32_t tmpreg = 0;
/* Check the parameters */
assert_param(IS_PWR_REGULATOR_VOLTAGE(PWR_Regulator_Voltage));
tmpreg = PWR->CR;
/* Clear VOS[15:14] bits */
tmpreg &= CR_VOS_MASK;
/* Set VOS[15:14] bits according to PWR_Regulator_Voltage value */
tmpreg |= PWR_Regulator_Voltage;
/* Store the new value */
PWR->CR = tmpreg;
}
/**
* @}
*/
/** @defgroup PWR_Group5 FLASH Power Down configuration functions
* @brief FLASH Power Down configuration functions
*
@verbatim
===============================================================================
##### FLASH Power Down configuration functions #####
===============================================================================
[..]
(+) By setting the FPDS bit in the PWR_CR register by using the
PWR_FlashPowerDownCmd() function, the Flash memory also enters power
down mode when the device enters Stop mode. When the Flash memory
is in power down mode, an additional startup delay is incurred when
waking up from Stop mode.
@endverbatim
* @{
*/
/**
* @brief Enables or disables the Flash Power Down in STOP mode.
* @param NewState: new state of the Flash power mode.
* This parameter can be: ENABLE or DISABLE.
* @retval None
*/
void PWR_FlashPowerDownCmd(FunctionalState NewState)
{
/* Check the parameters */
assert_param(IS_FUNCTIONAL_STATE(NewState));
*(__IO uint32_t *) CR_FPDS_BB = (uint32_t)NewState;
}
/**
* @}
*/
/** @defgroup PWR_Group6 Low Power modes configuration functions
* @brief Low Power modes configuration functions
*
@verbatim
===============================================================================
##### Low Power modes configuration functions #####
===============================================================================
[..]
The devices feature 3 low-power modes:
(+) Sleep mode: Cortex-M4 core stopped, peripherals kept running.
(+) Stop mode: all clocks are stopped, regulator running, regulator
in low power mode
(+) Standby mode: 1.2V domain powered off.
*** Sleep mode ***
==================
[..]
(+) Entry:
(++) The Sleep mode is entered by using the __WFI() or __WFE() functions.
(+) Exit:
(++) Any peripheral interrupt acknowledged by the nested vectored interrupt
controller (NVIC) can wake up the device from Sleep mode.
*** Stop mode ***
=================
[..]
In Stop mode, all clocks in the 1.2V domain are stopped, the PLL, the HSI,
and the HSE RC oscillators are disabled. Internal SRAM and register contents
are preserved.
The voltage regulator can be configured either in normal or low-power mode.
To minimize the consumption In Stop mode, FLASH can be powered off before
entering the Stop mode. It can be switched on again by software after exiting
the Stop mode using the PWR_FlashPowerDownCmd() function.
(+) Entry:
(++) The Stop mode is entered using the PWR_EnterSTOPMode(PWR_Regulator_LowPower,)
function with regulator in LowPower or with Regulator ON.
(+) Exit:
(++) Any EXTI Line (Internal or External) configured in Interrupt/Event mode.
*** Standby mode ***
====================
[..]
The Standby mode allows to achieve the lowest power consumption. It is based
on the Cortex-M4 deepsleep mode, with the voltage regulator disabled.
The 1.2V domain is consequently powered off. The PLL, the HSI oscillator and
the HSE oscillator are also switched off. SRAM and register contents are lost
except for the RTC registers, RTC backup registers, backup SRAM and Standby
circuitry.
The voltage regulator is OFF.
(+) Entry:
(++) The Standby mode is entered using the PWR_EnterSTANDBYMode() function.
(+) Exit:
(++) WKUP pin rising edge, RTC alarm (Alarm A and Alarm B), RTC wakeup,
tamper event, time-stamp event, external reset in NRST pin, IWDG reset.
*** Auto-wakeup (AWU) from low-power mode ***
=============================================
[..]
The MCU can be woken up from low-power mode by an RTC Alarm event, an RTC
Wakeup event, a tamper event, a time-stamp event, or a comparator event,
without depending on an external interrupt (Auto-wakeup mode).
(#) RTC auto-wakeup (AWU) from the Stop mode
(++) To wake up from the Stop mode with an RTC alarm event, it is necessary to:
(+++) Configure the EXTI Line 17 to be sensitive to rising edges (Interrupt
or Event modes) using the EXTI_Init() function.
(+++) Enable the RTC Alarm Interrupt using the RTC_ITConfig() function
(+++) Configure the RTC to generate the RTC alarm using the RTC_SetAlarm()
and RTC_AlarmCmd() functions.
(++) To wake up from the Stop mode with an RTC Tamper or time stamp event, it
is necessary to:
(+++) Configure the EXTI Line 21 to be sensitive to rising edges (Interrupt
or Event modes) using the EXTI_Init() function.
(+++) Enable the RTC Tamper or time stamp Interrupt using the RTC_ITConfig()
function
(+++) Configure the RTC to detect the tamper or time stamp event using the
RTC_TimeStampConfig(), RTC_TamperTriggerConfig() and RTC_TamperCmd()
functions.
(++) To wake up from the Stop mode with an RTC WakeUp event, it is necessary to:
(+++) Configure the EXTI Line 22 to be sensitive to rising edges (Interrupt
or Event modes) using the EXTI_Init() function.
(+++) Enable the RTC WakeUp Interrupt using the RTC_ITConfig() function
(+++) Configure the RTC to generate the RTC WakeUp event using the RTC_WakeUpClockConfig(),
RTC_SetWakeUpCounter() and RTC_WakeUpCmd() functions.
(#) RTC auto-wakeup (AWU) from the Standby mode
(++) To wake up from the Standby mode with an RTC alarm event, it is necessary to:
(+++) Enable the RTC Alarm Interrupt using the RTC_ITConfig() function
(+++) Configure the RTC to generate the RTC alarm using the RTC_SetAlarm()
and RTC_AlarmCmd() functions.
(++) To wake up from the Standby mode with an RTC Tamper or time stamp event, it
is necessary to:
(+++) Enable the RTC Tamper or time stamp Interrupt using the RTC_ITConfig()
function
(+++) Configure the RTC to detect the tamper or time stamp event using the
RTC_TimeStampConfig(), RTC_TamperTriggerConfig() and RTC_TamperCmd()
functions.
(++) To wake up from the Standby mode with an RTC WakeUp event, it is necessary to:
(+++) Enable the RTC WakeUp Interrupt using the RTC_ITConfig() function
(+++) Configure the RTC to generate the RTC WakeUp event using the RTC_WakeUpClockConfig(),
RTC_SetWakeUpCounter() and RTC_WakeUpCmd() functions.
@endverbatim
* @{
*/
/**
* @brief Enters STOP mode.
*
* @note In Stop mode, all I/O pins keep the same state as in Run mode.
* @note When exiting Stop mode by issuing an interrupt or a wakeup event,
* the HSI RC oscillator is selected as system clock.
* @note When the voltage regulator operates in low power mode, an additional
* startup delay is incurred when waking up from Stop mode.
* By keeping the internal regulator ON during Stop mode, the consumption
* is higher although the startup time is reduced.
*
* @param PWR_Regulator: specifies the regulator state in STOP mode.
* This parameter can be one of the following values:
* @arg PWR_Regulator_ON: STOP mode with regulator ON
* @arg PWR_Regulator_LowPower: STOP mode with regulator in low power mode
* @param PWR_STOPEntry: specifies if STOP mode in entered with WFI or WFE instruction.
* This parameter can be one of the following values:
* @arg PWR_STOPEntry_WFI: enter STOP mode with WFI instruction
* @arg PWR_STOPEntry_WFE: enter STOP mode with WFE instruction
* @retval None
*/
void PWR_EnterSTOPMode(uint32_t PWR_Regulator, uint8_t PWR_STOPEntry)
{
uint32_t tmpreg = 0;
/* Check the parameters */
assert_param(IS_PWR_REGULATOR(PWR_Regulator));
assert_param(IS_PWR_STOP_ENTRY(PWR_STOPEntry));
/* Select the regulator state in STOP mode ---------------------------------*/
tmpreg = PWR->CR;
/* Clear PDDS and LPDSR bits */
tmpreg &= CR_DS_MASK;
/* Set LPDSR bit according to PWR_Regulator value */
tmpreg |= PWR_Regulator;
/* Store the new value */
PWR->CR = tmpreg;
/* Set SLEEPDEEP bit of Cortex System Control Register */
SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;
/* Select STOP mode entry --------------------------------------------------*/
if(PWR_STOPEntry == PWR_STOPEntry_WFI)
{
/* Request Wait For Interrupt */
__WFI();
}
else
{
/* Request Wait For Event */
__WFE();
}
/* Reset SLEEPDEEP bit of Cortex System Control Register */
SCB->SCR &= (uint32_t)~((uint32_t)SCB_SCR_SLEEPDEEP_Msk);
}
/**
* @brief Enters STANDBY mode.
* @note In Standby mode, all I/O pins are high impedance except for:
* - Reset pad (still available)
* - RTC_AF1 pin (PC13) if configured for tamper, time-stamp, RTC
* Alarm out, or RTC clock calibration out.
* - RTC_AF2 pin (PI8) if configured for tamper or time-stamp.
* - WKUP pin 1 (PA0) if enabled.
* @param None
* @retval None
*/
void PWR_EnterSTANDBYMode(void)
{
/* Clear Wakeup flag */
PWR->CR |= PWR_CR_CWUF;
/* Select STANDBY mode */
PWR->CR |= PWR_CR_PDDS;
/* Set SLEEPDEEP bit of Cortex System Control Register */
SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;
/* This option is used to ensure that store operations are completed */
#if defined ( __CC_ARM )
__force_stores();
#endif
/* Request Wait For Interrupt */
__WFI();
}
/**
* @}
*/
/** @defgroup PWR_Group7 Flags management functions
* @brief Flags management functions
*
@verbatim
===============================================================================
##### Flags management functions #####
===============================================================================
@endverbatim
* @{
*/
/**
* @brief Checks whether the specified PWR flag is set or not.
* @param PWR_FLAG: specifies the flag to check.
* This parameter can be one of the following values:
* @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
* was received from the WKUP pin or from the RTC alarm (Alarm A
* or Alarm B), RTC Tamper event, RTC TimeStamp event or RTC Wakeup.
* An additional wakeup event is detected if the WKUP pin is enabled
* (by setting the EWUP bit) when the WKUP pin level is already high.
* @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
* resumed from StandBy mode.
* @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
* by the PWR_PVDCmd() function. The PVD is stopped by Standby mode
* For this reason, this bit is equal to 0 after Standby or reset
* until the PVDE bit is set.
* @arg PWR_FLAG_BRR: Backup regulator ready flag. This bit is not reset
* when the device wakes up from Standby mode or by a system reset
* or power reset.
* @arg PWR_FLAG_VOSRDY: This flag indicates that the Regulator voltage
* scaling output selection is ready.
* @retval The new state of PWR_FLAG (SET or RESET).
*/
FlagStatus PWR_GetFlagStatus(uint32_t PWR_FLAG)
{
FlagStatus bitstatus = RESET;
/* Check the parameters */
assert_param(IS_PWR_GET_FLAG(PWR_FLAG));
if ((PWR->CSR & PWR_FLAG) != (uint32_t)RESET)
{
bitstatus = SET;
}
else
{
bitstatus = RESET;
}
/* Return the flag status */
return bitstatus;
}
/**
* @brief Clears the PWR's pending flags.
* @param PWR_FLAG: specifies the flag to clear.
* This parameter can be one of the following values:
* @arg PWR_FLAG_WU: Wake Up flag
* @arg PWR_FLAG_SB: StandBy flag
* @retval None
*/
void PWR_ClearFlag(uint32_t PWR_FLAG)
{
/* Check the parameters */
assert_param(IS_PWR_CLEAR_FLAG(PWR_FLAG));
PWR->CR |= PWR_FLAG << 2;
}
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
Reference in New Issue Copy Permalink