circuitpython/ports/stm32/boards/NUCLEO_F401RE/mpconfigboard.h

Ignoring revisions in .git-blame-ignore-revs. Click here to bypass and see the normal blame view.

68 lines
2.9 KiB
C
Raw Normal View History

#define MICROPY_HW_BOARD_NAME "NUCLEO-F401RE"
#define MICROPY_HW_MCU_NAME "STM32F401xE"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_SERVO (1)
// HSE is 8MHz, HSI is 16MHz CPU freq set to 84MHz
// Default source for the clock is HSI.
// For revisions of the board greater than C-01, HSE can be used as a
// clock source by removing the #define MICROPY_HW_CLK_USE_HSE line
#define MICROPY_HW_CLK_USE_HSI (1)
#if MICROPY_HW_CLK_USE_HSI
#define MICROPY_HW_CLK_PLLM (16)
#else
#define MICROPY_HW_CLK_PLLM (8)
#endif
#define MICROPY_HW_CLK_PLLN (336)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV4)
#define MICROPY_HW_CLK_PLLQ (7)
// UART config
#define MICROPY_HW_UART2_TX (pin_A2)
#define MICROPY_HW_UART2_RX (pin_A3)
#define MICROPY_HW_UART6_TX (pin_C6)
#define MICROPY_HW_UART6_RX (pin_C7)
// UART 2 connects to the STM32F103 (STLINK) on the Nucleo board
// and this is exposed as a USB Serial port.
#define MICROPY_HW_UART_REPL PYB_UART_2
#define MICROPY_HW_UART_REPL_BAUD 115200
// I2C buses
#define MICROPY_HW_I2C1_SCL (pin_B8) // Arduino D15, pin 3 on CN10
#define MICROPY_HW_I2C1_SDA (pin_B9) // D14, pin 5 on CN10
#define MICROPY_HW_I2C2_SCL (pin_B10) // Arduino D6, pin 25 on CN10
#define MICROPY_HW_I2C2_SDA (pin_B3) // Arduino D3, pin 31 on CN10
#define MICROPY_HW_I2C3_SCL (pin_A8) // Arduino D7, pin 23 on CN10
#define MICROPY_HW_I2C3_SDA (pin_C9) // pin 1 on CN10
// SPI buses
#define MICROPY_HW_SPI1_NSS (pin_A15) // pin 17 on CN7
#define MICROPY_HW_SPI1_SCK (pin_A5) // Arduino D13, pin 11 on CN10
#define MICROPY_HW_SPI1_MISO (pin_A6) // Arduino D12, pin 13 on CN10
#define MICROPY_HW_SPI1_MOSI (pin_A7) // Arduino D11, pin 15 on CN10
#define MICROPY_HW_SPI2_NSS (pin_B12) // pin 16 on CN10
#define MICROPY_HW_SPI2_SCK (pin_B13) // pin 30 on CN10
#define MICROPY_HW_SPI2_MISO (pin_B14) // pin 28 on CN10
#define MICROPY_HW_SPI2_MOSI (pin_B15) // pin 26 on CN10
#define MICROPY_HW_SPI3_NSS (pin_A4) // Arduino A2, pin 32 on CN7
#define MICROPY_HW_SPI3_SCK (pin_B3) // Arduino D3, pin 31 on CN10
#define MICROPY_HW_SPI3_MISO (pin_B4) // Arduino D5, pin 27 on CN10
#define MICROPY_HW_SPI3_MOSI (pin_B5) // Arduino D4, pin 29 on CN10
// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN (pin_C13)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_FALLING)
#define MICROPY_HW_USRSW_PRESSED (0)
// LEDs
#define MICROPY_HW_LED1 (pin_A5) // Green LD2 LED on Nucleo
#define MICROPY_HW_LED_ON(pin) (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin) (mp_hal_pin_low(pin))