circuitpython/ports/stm32/usbd_conf.c

624 lines
19 KiB
C
Raw Normal View History

/*
* This file is part of the MicroPython project, http://micropython.org/
*/
/**
******************************************************************************
* @file USB_Device/CDC_Standalone/Src/usbd_conf.c
* @author MCD Application Team
* @version V1.0.1
* @date 26-February-2014
* @brief This file implements the USB Device library callbacks and MSP
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
#include "usbd_core.h"
#include "py/obj.h"
#include "py/mphal.h"
#include "irq.h"
#include "usb.h"
#if MICROPY_HW_USB_FS || MICROPY_HW_USB_HS
#if MICROPY_HW_USB_FS
PCD_HandleTypeDef pcd_fs_handle;
#endif
#if MICROPY_HW_USB_HS
PCD_HandleTypeDef pcd_hs_handle;
#endif
/*******************************************************************************
PCD BSP Routines
*******************************************************************************/
/**
* @brief Initializes the PCD MSP.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_MspInit(PCD_HandleTypeDef *hpcd) {
if (hpcd->Instance == USB_OTG_FS) {
#if defined(STM32H7)
const uint32_t otg_alt = GPIO_AF10_OTG1_FS;
#else
const uint32_t otg_alt = GPIO_AF10_OTG_FS;
#endif
mp_hal_pin_config(pin_A11, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, otg_alt);
mp_hal_pin_config_speed(pin_A11, GPIO_SPEED_FREQ_VERY_HIGH);
mp_hal_pin_config(pin_A12, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, otg_alt);
mp_hal_pin_config_speed(pin_A12, GPIO_SPEED_FREQ_VERY_HIGH);
#if defined(MICROPY_HW_USB_VBUS_DETECT_PIN)
// USB VBUS detect pin is always A9
mp_hal_pin_config(MICROPY_HW_USB_VBUS_DETECT_PIN, MP_HAL_PIN_MODE_INPUT, MP_HAL_PIN_PULL_NONE, 0);
#endif
#if defined(MICROPY_HW_USB_OTG_ID_PIN)
// USB ID pin is always A10
mp_hal_pin_config(MICROPY_HW_USB_OTG_ID_PIN, MP_HAL_PIN_MODE_ALT_OPEN_DRAIN, MP_HAL_PIN_PULL_UP, otg_alt);
#endif
#if defined(STM32H7)
// Keep USB clock running during sleep or else __WFI() will disable the USB
__HAL_RCC_USB2_OTG_FS_CLK_SLEEP_ENABLE();
__HAL_RCC_USB2_OTG_FS_ULPI_CLK_SLEEP_DISABLE();
#endif
// Enable USB FS Clocks
__USB_OTG_FS_CLK_ENABLE();
#if defined(STM32L4)
// Enable VDDUSB
if (__HAL_RCC_PWR_IS_CLK_DISABLED()) {
__HAL_RCC_PWR_CLK_ENABLE();
HAL_PWREx_EnableVddUSB();
__HAL_RCC_PWR_CLK_DISABLE();
} else {
HAL_PWREx_EnableVddUSB();
}
#endif
// Configure and enable USB FS interrupt
NVIC_SetPriority(OTG_FS_IRQn, IRQ_PRI_OTG_FS);
HAL_NVIC_EnableIRQ(OTG_FS_IRQn);
}
#if MICROPY_HW_USB_HS
else if (hpcd->Instance == USB_OTG_HS) {
#if MICROPY_HW_USB_HS_IN_FS
#if defined(STM32H7)
const uint32_t otg_alt = GPIO_AF12_OTG2_FS;
#else
const uint32_t otg_alt = GPIO_AF12_OTG_HS_FS;
#endif
// Configure USB FS GPIOs
mp_hal_pin_config(pin_B14, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, otg_alt);
mp_hal_pin_config_speed(pin_B14, GPIO_SPEED_FREQ_VERY_HIGH);
mp_hal_pin_config(pin_B15, MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, otg_alt);
mp_hal_pin_config_speed(pin_B15, GPIO_SPEED_FREQ_VERY_HIGH);
#if defined(MICROPY_HW_USB_VBUS_DETECT_PIN)
// Configure VBUS Pin
mp_hal_pin_config(MICROPY_HW_USB_VBUS_DETECT_PIN, MP_HAL_PIN_MODE_INPUT, MP_HAL_PIN_PULL_NONE, 0);
#endif
#if defined(MICROPY_HW_USB_OTG_ID_PIN)
// Configure ID pin
mp_hal_pin_config(MICROPY_HW_USB_OTG_ID_PIN, MP_HAL_PIN_MODE_ALT_OPEN_DRAIN, MP_HAL_PIN_PULL_UP, otg_alt);
#endif
// Enable calling WFI and correct function of the embedded USB_FS_IN_HS phy
__HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_DISABLE();
__HAL_RCC_USB_OTG_HS_CLK_SLEEP_ENABLE();
// Enable USB HS Clocks
#if defined(STM32F723xx) || defined(STM32F733xx)
// Needs to remain awake during sleep or else __WFI() will disable the USB
__HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_ENABLE();
__HAL_RCC_OTGPHYC_CLK_ENABLE();
__HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE();
#endif
__HAL_RCC_USB_OTG_HS_CLK_ENABLE();
#else // !MICROPY_HW_USB_HS_IN_FS
// Configure USB HS GPIOs
static const mp_hal_pin_obj_t usb_pins[] = {
pin_A5, pin_C0, pin_H4, pin_I11, // CLK, STP, NXT, DIR
pin_A3, pin_B0, pin_B1, pin_B5, pin_B10, pin_B11, pin_B12, pin_B13, // D0-D7
};
for (size_t i = 0; i < MP_ARRAY_SIZE(usb_pins); ++i) {
mp_hal_pin_config(usb_pins[i], MP_HAL_PIN_MODE_ALT, MP_HAL_PIN_PULL_NONE, GPIO_AF10_OTG_HS);
mp_hal_pin_config_speed(usb_pins[i], GPIO_SPEED_FREQ_VERY_HIGH);
}
// Enable USB HS Clocks
__HAL_RCC_USB_OTG_HS_CLK_ENABLE();
__HAL_RCC_USB_OTG_HS_CLK_SLEEP_ENABLE();
__HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE();
__HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_ENABLE();
#endif // !MICROPY_HW_USB_HS_IN_FS
// Configure and enable USB HS interrupt
NVIC_SetPriority(OTG_HS_IRQn, IRQ_PRI_OTG_HS);
HAL_NVIC_EnableIRQ(OTG_HS_IRQn);
}
#endif // MICROPY_HW_USB_HS
}
/**
* @brief DeInitializes the PCD MSP.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_MspDeInit(PCD_HandleTypeDef *hpcd) {
if (hpcd->Instance == USB_OTG_FS) {
/* Disable USB FS Clocks */
__USB_OTG_FS_CLK_DISABLE();
__SYSCFG_CLK_DISABLE();
}
#if MICROPY_HW_USB_HS
else if (hpcd->Instance == USB_OTG_HS) {
/* Disable USB FS Clocks */
__USB_OTG_HS_CLK_DISABLE();
__SYSCFG_CLK_DISABLE();
}
#endif
}
/*******************************************************************************
LL Driver Callbacks (PCD -> USB Device Library)
*******************************************************************************/
/**
* @brief Setup stage callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_SetupStageCallback(PCD_HandleTypeDef *hpcd) {
USBD_LL_SetupStage(hpcd->pData, (uint8_t *)hpcd->Setup);
}
/**
* @brief Data Out stage callback.
* @param hpcd: PCD handle
* @param epnum: Endpoint Number
* @retval None
*/
void HAL_PCD_DataOutStageCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum) {
USBD_LL_DataOutStage(hpcd->pData, epnum, hpcd->OUT_ep[epnum].xfer_buff);
}
/**
* @brief Data In stage callback.
* @param hpcd: PCD handle
* @param epnum: Endpoint Number
* @retval None
*/
void HAL_PCD_DataInStageCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum) {
USBD_LL_DataInStage(hpcd->pData, epnum, hpcd->IN_ep[epnum].xfer_buff);
}
/**
* @brief SOF callback.
* @param hpcd: PCD handle
* @retval None
*/
/*
This is now handled by the USB CDC interface.
void HAL_PCD_SOFCallback(PCD_HandleTypeDef *hpcd)
{
USBD_LL_SOF(hpcd->pData);
}
*/
/**
* @brief Reset callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_ResetCallback(PCD_HandleTypeDef *hpcd) {
USBD_SpeedTypeDef speed = USBD_SPEED_FULL;
// Set USB Current Speed
switch (hpcd->Init.speed) {
#if defined(PCD_SPEED_HIGH)
case PCD_SPEED_HIGH:
speed = USBD_SPEED_HIGH;
break;
#endif
case PCD_SPEED_FULL:
speed = USBD_SPEED_FULL;
break;
default:
speed = USBD_SPEED_FULL;
break;
}
USBD_LL_SetSpeed(hpcd->pData, speed);
// Reset Device
USBD_LL_Reset(hpcd->pData);
}
/**
* @brief Suspend callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_SuspendCallback(PCD_HandleTypeDef *hpcd) {
USBD_LL_Suspend(hpcd->pData);
}
/**
* @brief Resume callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_ResumeCallback(PCD_HandleTypeDef *hpcd) {
USBD_LL_Resume(hpcd->pData);
}
/**
* @brief ISOC Out Incomplete callback.
* @param hpcd: PCD handle
* @param epnum: Endpoint Number
* @retval None
*/
void HAL_PCD_ISOOUTIncompleteCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum) {
USBD_LL_IsoOUTIncomplete(hpcd->pData, epnum);
}
/**
* @brief ISOC In Incomplete callback.
* @param hpcd: PCD handle
* @param epnum: Endpoint Number
* @retval None
*/
void HAL_PCD_ISOINIncompleteCallback(PCD_HandleTypeDef *hpcd, uint8_t epnum) {
USBD_LL_IsoINIncomplete(hpcd->pData, epnum);
}
/**
* @brief Connect callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_ConnectCallback(PCD_HandleTypeDef *hpcd) {
USBD_LL_DevConnected(hpcd->pData);
}
/**
* @brief Disconnect callback.
* @param hpcd: PCD handle
* @retval None
*/
void HAL_PCD_DisconnectCallback(PCD_HandleTypeDef *hpcd) {
USBD_LL_DevDisconnected(hpcd->pData);
}
/*******************************************************************************
LL Driver Interface (USB Device Library --> PCD)
*******************************************************************************/
/**
* @brief Initializes the Low Level portion of the Device driver.
* @param pdev: Device handle
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_Init(USBD_HandleTypeDef *pdev, int high_speed) {
#if MICROPY_HW_USB_FS
if (pdev->id == USB_PHY_FS_ID) {
// Set LL Driver parameters
pcd_fs_handle.Instance = USB_OTG_FS;
#if MICROPY_HW_USB_CDC_NUM == 2
pcd_fs_handle.Init.dev_endpoints = 6;
#else
pcd_fs_handle.Init.dev_endpoints = 4;
#endif
pcd_fs_handle.Init.use_dedicated_ep1 = 0;
pcd_fs_handle.Init.ep0_mps = 0x40;
pcd_fs_handle.Init.dma_enable = 0;
pcd_fs_handle.Init.low_power_enable = 0;
pcd_fs_handle.Init.phy_itface = PCD_PHY_EMBEDDED;
stm32/usbd_cdc_interface: Refactor USB CDC tx code to not use SOF IRQ. Prior to this commit the USB CDC used the USB start-of-frame (SOF) IRQ to regularly check if buffered data needed to be sent out to the USB host. This wasted resources (CPU, power) if no data needed to be sent. This commit changes how the USB CDC transmits buffered data: - When new data is first available to send the data is queued immediately on the USB IN endpoint, ready to be sent as soon as possible. - Subsequent additions to the buffer (via usbd_cdc_try_tx()) will wait. - When the low-level USB driver has finished sending out the data queued in the USB IN endpoint it calls usbd_cdc_tx_ready() which immediately queues any outstanding data, waiting for the next IN frame. The benefits on this new approach are: - SOF IRQ does not need to run continuously so device has a better chance to sleep for longer, and be more responsive to other IRQs. - Because SOF IRQ is off, current consumption is reduced by a small amount, roughly 200uA when USB is connected (measured on PYBv1.0). - CDC tx throughput (USB IN) on PYBv1.0 is about 2.3 faster (USB OUT is unchanged). - When USB is connected, Python code that is executing is slightly faster because SOF IRQ no longer interrupts continuously. - On F733 with USB HS, CDC tx throughput is about the same as prior to this commit. - On F733 with USB HS, Python code is about 5% faster because of no SOF. As part of this refactor, the serial port should no longer echo initial characters when the serial port is first opened (this only used to happen rarely on USB FS, but on USB HS is was more evident).
2018-10-15 00:35:10 -04:00
pcd_fs_handle.Init.Sof_enable = 0;
pcd_fs_handle.Init.speed = PCD_SPEED_FULL;
#if defined(STM32L4)
pcd_fs_handle.Init.lpm_enable = DISABLE;
pcd_fs_handle.Init.battery_charging_enable = DISABLE;
#endif
#if !defined(MICROPY_HW_USB_VBUS_DETECT_PIN)
pcd_fs_handle.Init.vbus_sensing_enable = 0; // No VBUS Sensing on USB0
#else
pcd_fs_handle.Init.vbus_sensing_enable = 1;
#endif
// Link The driver to the stack
pcd_fs_handle.pData = pdev;
pdev->pData = &pcd_fs_handle;
// Initialize LL Driver
HAL_PCD_Init(&pcd_fs_handle);
// We have 320 32-bit words in total to use here
#if MICROPY_HW_USB_CDC_NUM == 2
HAL_PCD_SetRxFiFo(&pcd_fs_handle, 128);
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 0, 32); // EP0
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 1, 64); // MSC / HID
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 2, 16); // CDC CMD
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 3, 32); // CDC DATA
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 4, 16); // CDC2 CMD
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 5, 32); // CDC2 DATA
#else
HAL_PCD_SetRxFiFo(&pcd_fs_handle, 128);
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 0, 32); // EP0
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 1, 64); // MSC / HID
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 2, 32); // CDC CMD
HAL_PCD_SetTxFiFo(&pcd_fs_handle, 3, 64); // CDC DATA
#endif
}
#endif
#if MICROPY_HW_USB_HS
if (pdev->id == USB_PHY_HS_ID) {
// Set LL Driver parameters
pcd_hs_handle.Instance = USB_OTG_HS;
#if MICROPY_HW_USB_CDC_NUM == 3
pcd_hs_handle.Init.dev_endpoints = 8;
#else
pcd_hs_handle.Init.dev_endpoints = 6;
#endif
pcd_hs_handle.Init.use_dedicated_ep1 = 0;
pcd_hs_handle.Init.ep0_mps = 0x40;
pcd_hs_handle.Init.dma_enable = 0;
pcd_hs_handle.Init.low_power_enable = 0;
pcd_hs_handle.Init.lpm_enable = DISABLE;
pcd_hs_handle.Init.battery_charging_enable = DISABLE;
pcd_hs_handle.Init.Sof_enable = 0;
pcd_hs_handle.Init.use_external_vbus = 0;
#if !defined(MICROPY_HW_USB_VBUS_DETECT_PIN)
pcd_hs_handle.Init.vbus_sensing_enable = 0; // No VBUS Sensing on USB0
#else
pcd_hs_handle.Init.vbus_sensing_enable = 1;
#endif
#if MICROPY_HW_USB_HS_IN_FS
#if defined(STM32F723xx) || defined(STM32F733xx)
pcd_hs_handle.Init.phy_itface = USB_OTG_HS_EMBEDDED_PHY;
#else
pcd_hs_handle.Init.phy_itface = PCD_PHY_EMBEDDED;
#endif
if (high_speed) {
pcd_hs_handle.Init.speed = PCD_SPEED_HIGH;
} else {
pcd_hs_handle.Init.speed = PCD_SPEED_HIGH_IN_FULL;
}
#else
// USB HS with external PHY
pcd_hs_handle.Init.phy_itface = PCD_PHY_ULPI;
pcd_hs_handle.Init.speed = PCD_SPEED_HIGH;
#endif
// Link The driver to the stack
pcd_hs_handle.pData = pdev;
pdev->pData = &pcd_hs_handle;
// Initialize LL Driver
HAL_PCD_Init(&pcd_hs_handle);
// We have 1024 32-bit words in total to use here
#if MICROPY_HW_USB_CDC_NUM == 3
HAL_PCD_SetRxFiFo(&pcd_hs_handle, 328);
#else
HAL_PCD_SetRxFiFo(&pcd_hs_handle, 464);
#endif
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 0, 32); // EP0
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 1, 256); // MSC / HID
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 2, 8); // CDC CMD
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 3, 128); // CDC DATA
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 4, 8); // CDC2 CMD
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 5, 128); // CDC2 DATA
#if MICROPY_HW_USB_CDC_NUM == 3
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 6, 8); // CDC3 CMD
HAL_PCD_SetTxFiFo(&pcd_hs_handle, 7, 128); // CDC3 DATA
#endif
}
#endif // MICROPY_HW_USB_HS
return USBD_OK;
}
/**
* @brief De-Initializes the Low Level portion of the Device driver.
* @param pdev: Device handle
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_DeInit(USBD_HandleTypeDef *pdev) {
HAL_PCD_DeInit(pdev->pData);
return USBD_OK;
}
/**
* @brief Starts the Low Level portion of the Device driver.
* @param pdev: Device handle
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_Start(USBD_HandleTypeDef *pdev) {
HAL_PCD_Start(pdev->pData);
return USBD_OK;
}
/**
* @brief Stops the Low Level portion of the Device driver.
* @param pdev: Device handle
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_Stop(USBD_HandleTypeDef *pdev) {
HAL_PCD_Stop(pdev->pData);
return USBD_OK;
}
/**
* @brief Opens an endpoint of the Low Level Driver.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @param ep_type: Endpoint Type
* @param ep_mps: Endpoint Max Packet Size
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_OpenEP(USBD_HandleTypeDef *pdev,
uint8_t ep_addr, uint8_t ep_type, uint16_t ep_mps) {
HAL_PCD_EP_Open(pdev->pData, ep_addr, ep_mps, ep_type);
return USBD_OK;
}
/**
* @brief Closes an endpoint of the Low Level Driver.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_CloseEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr) {
HAL_PCD_EP_Close(pdev->pData, ep_addr);
return USBD_OK;
}
/**
* @brief Flushes an endpoint of the Low Level Driver.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_FlushEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr) {
HAL_PCD_EP_Flush(pdev->pData, ep_addr);
return USBD_OK;
}
/**
* @brief Sets a Stall condition on an endpoint of the Low Level Driver.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_StallEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr) {
HAL_PCD_EP_SetStall(pdev->pData, ep_addr);
return USBD_OK;
}
/**
* @brief Clears a Stall condition on an endpoint of the Low Level Driver.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_ClearStallEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr) {
HAL_PCD_EP_ClrStall(pdev->pData, ep_addr);
return USBD_OK;
}
/**
* @brief Returns Stall condition.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval Stall (1: yes, 0: No)
*/
uint8_t USBD_LL_IsStallEP(USBD_HandleTypeDef *pdev, uint8_t ep_addr) {
PCD_HandleTypeDef *hpcd = pdev->pData;
if ((ep_addr & 0x80) == 0x80) {
return hpcd->IN_ep[ep_addr & 0x7F].is_stall;
} else {
return hpcd->OUT_ep[ep_addr & 0x7F].is_stall;
}
}
/**
* @brief Assigns an USB address to the device
* @param pdev: Device handle
* @param dev_addr: USB address
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_SetUSBAddress(USBD_HandleTypeDef *pdev, uint8_t dev_addr) {
HAL_PCD_SetAddress(pdev->pData, dev_addr);
return USBD_OK;
}
/**
* @brief Transmits data over an endpoint
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @param pbuf: Pointer to data to be sent
* @param size: Data size
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_Transmit(USBD_HandleTypeDef *pdev,
uint8_t ep_addr, uint8_t *pbuf, uint16_t size) {
HAL_PCD_EP_Transmit(pdev->pData, ep_addr, pbuf, size);
return USBD_OK;
}
/**
* @brief Prepares an endpoint for reception
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @param pbuf:pointer to data to be received
* @param size: data size
* @retval USBD Status
*/
USBD_StatusTypeDef USBD_LL_PrepareReceive(USBD_HandleTypeDef *pdev,
uint8_t ep_addr, uint8_t *pbuf, uint16_t size) {
HAL_PCD_EP_Receive(pdev->pData, ep_addr, pbuf, size);
return USBD_OK;
}
/**
* @brief Returns the last transfered packet size.
* @param pdev: Device handle
* @param ep_addr: Endpoint Number
* @retval Recived Data Size
*/
uint32_t USBD_LL_GetRxDataSize(USBD_HandleTypeDef *pdev, uint8_t ep_addr) {
return HAL_PCD_EP_GetRxCount(pdev->pData, ep_addr);
}
/**
* @brief Delay routine for the USB Device Library
* @param Delay: Delay in ms
* @retval None
*/
void USBD_LL_Delay(uint32_t Delay) {
HAL_Delay(Delay);
}
#endif // MICROPY_HW_USB_FS || MICROPY_HW_USB_HS
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/