circuitpython/stm/lib/stm32f4xx_syscfg.c

208 lines
7.6 KiB
C
Raw Normal View History

2013-11-01 18:27:51 -04:00
/**
******************************************************************************
* @file stm32f4xx_syscfg.c
* @author MCD Application Team
* @version V1.1.0
* @date 11-January-2013
* @brief This file provides firmware functions to manage the SYSCFG peripheral.
*
@verbatim
===============================================================================
##### How to use this driver #####
===============================================================================
[..] This driver provides functions for:
(#) Remapping the memory accessible in the code area using SYSCFG_MemoryRemapConfig()
(#) Manage the EXTI lines connection to the GPIOs using SYSCFG_EXTILineConfig()
(#) Select the ETHERNET media interface (RMII/RII) using SYSCFG_ETH_MediaInterfaceConfig()
-@- SYSCFG APB clock must be enabled to get write access to SYSCFG registers,
using RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT 2013 STMicroelectronics</center></h2>
*
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
* You may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.st.com/software_license_agreement_liberty_v2
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_conf.h"
#include "stm32f4xx_syscfg.h"
#include "stm32f4xx_rcc.h"
/** @addtogroup STM32F4xx_StdPeriph_Driver
* @{
*/
/** @defgroup SYSCFG
* @brief SYSCFG driver modules
* @{
*/
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* ------------ RCC registers bit address in the alias region ----------- */
#define SYSCFG_OFFSET (SYSCFG_BASE - PERIPH_BASE)
/* --- PMC Register ---*/
/* Alias word address of MII_RMII_SEL bit */
#define PMC_OFFSET (SYSCFG_OFFSET + 0x04)
#define MII_RMII_SEL_BitNumber ((uint8_t)0x17)
#define PMC_MII_RMII_SEL_BB (PERIPH_BB_BASE + (PMC_OFFSET * 32) + (MII_RMII_SEL_BitNumber * 4))
/* --- CMPCR Register ---*/
/* Alias word address of CMP_PD bit */
#define CMPCR_OFFSET (SYSCFG_OFFSET + 0x20)
#define CMP_PD_BitNumber ((uint8_t)0x00)
#define CMPCR_CMP_PD_BB (PERIPH_BB_BASE + (CMPCR_OFFSET * 32) + (CMP_PD_BitNumber * 4))
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup SYSCFG_Private_Functions
* @{
*/
/**
* @brief Deinitializes the Alternate Functions (remap and EXTI configuration)
* registers to their default reset values.
* @param None
* @retval None
*/
void SYSCFG_DeInit(void)
{
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SYSCFG, ENABLE);
RCC_APB2PeriphResetCmd(RCC_APB2Periph_SYSCFG, DISABLE);
}
/**
* @brief Changes the mapping of the specified pin.
* @param SYSCFG_Memory: selects the memory remapping.
* This parameter can be one of the following values:
* @arg SYSCFG_MemoryRemap_Flash: Main Flash memory mapped at 0x00000000
* @arg SYSCFG_MemoryRemap_SystemFlash: System Flash memory mapped at 0x00000000
* @arg SYSCFG_MemoryRemap_FSMC: FSMC (Bank1 (NOR/PSRAM 1 and 2) mapped at 0x00000000
* @arg SYSCFG_MemoryRemap_SRAM: Embedded SRAM (112kB) mapped at 0x00000000
* @retval None
*/
void SYSCFG_MemoryRemapConfig(uint8_t SYSCFG_MemoryRemap)
{
/* Check the parameters */
assert_param(IS_SYSCFG_MEMORY_REMAP_CONFING(SYSCFG_MemoryRemap));
SYSCFG->MEMRMP = SYSCFG_MemoryRemap;
}
/**
* @brief Selects the GPIO pin used as EXTI Line.
* @param EXTI_PortSourceGPIOx : selects the GPIO port to be used as source for
* EXTI lines where x can be (A..I) for STM32F40xx/STM32F41xx
* and STM32F427x/STM32F437x devices.
*
* @param EXTI_PinSourcex: specifies the EXTI line to be configured.
* This parameter can be EXTI_PinSourcex where x can be (0..15, except
* for EXTI_PortSourceGPIOI x can be (0..11) for STM32F40xx/STM32F41xx
* and STM32F427x/STM32F437x devices.
*
* @retval None
*/
void SYSCFG_EXTILineConfig(uint8_t EXTI_PortSourceGPIOx, uint8_t EXTI_PinSourcex)
{
uint32_t tmp = 0x00;
/* Check the parameters */
assert_param(IS_EXTI_PORT_SOURCE(EXTI_PortSourceGPIOx));
assert_param(IS_EXTI_PIN_SOURCE(EXTI_PinSourcex));
tmp = ((uint32_t)0x0F) << (0x04 * (EXTI_PinSourcex & (uint8_t)0x03));
SYSCFG->EXTICR[EXTI_PinSourcex >> 0x02] &= ~tmp;
SYSCFG->EXTICR[EXTI_PinSourcex >> 0x02] |= (((uint32_t)EXTI_PortSourceGPIOx) << (0x04 * (EXTI_PinSourcex & (uint8_t)0x03)));
}
/**
* @brief Selects the ETHERNET media interface
* @param SYSCFG_ETH_MediaInterface: specifies the Media Interface mode.
* This parameter can be one of the following values:
* @arg SYSCFG_ETH_MediaInterface_MII: MII mode selected
* @arg SYSCFG_ETH_MediaInterface_RMII: RMII mode selected
* @retval None
*/
void SYSCFG_ETH_MediaInterfaceConfig(uint32_t SYSCFG_ETH_MediaInterface)
{
assert_param(IS_SYSCFG_ETH_MEDIA_INTERFACE(SYSCFG_ETH_MediaInterface));
/* Configure MII_RMII selection bit */
*(__IO uint32_t *) PMC_MII_RMII_SEL_BB = SYSCFG_ETH_MediaInterface;
}
/**
* @brief Enables or disables the I/O Compensation Cell.
* @note The I/O compensation cell can be used only when the device supply
* voltage ranges from 2.4 to 3.6 V.
* @param NewState: new state of the I/O Compensation Cell.
* This parameter can be one of the following values:
* @arg ENABLE: I/O compensation cell enabled
* @arg DISABLE: I/O compensation cell power-down mode
* @retval None
*/
void SYSCFG_CompensationCellCmd(FunctionalState NewState)
{
/* Check the parameters */
assert_param(IS_FUNCTIONAL_STATE(NewState));
*(__IO uint32_t *) CMPCR_CMP_PD_BB = (uint32_t)NewState;
}
/**
* @brief Checks whether the I/O Compensation Cell ready flag is set or not.
* @param None
* @retval The new state of the I/O Compensation Cell ready flag (SET or RESET)
*/
FlagStatus SYSCFG_GetCompensationCellStatus(void)
{
FlagStatus bitstatus = RESET;
if ((SYSCFG->CMPCR & SYSCFG_CMPCR_READY ) != (uint32_t)RESET)
{
bitstatus = SET;
}
else
{
bitstatus = RESET;
}
return bitstatus;
}
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/