2016-02-08 23:36:51 -05:00
|
|
|
#define MICROPY_HW_BOARD_NAME "CustomPCB"
|
|
|
|
|
#define MICROPY_HW_MCU_NAME "STM32F439"
|
|
|
|
|
|
|
|
|
|
#define MICROPY_HW_HAS_FLASH (1)
|
|
|
|
|
#define MICROPY_HW_HAS_SDCARD (1) //works with no SD card too
|
|
|
|
|
#define MICROPY_HW_ENABLE_RNG (1)
|
|
|
|
|
#define MICROPY_HW_ENABLE_RTC (1)
|
|
|
|
|
#define MICROPY_HW_ENABLE_DAC (1)
|
|
|
|
|
#define MICROPY_HW_ENABLE_CAN (1)
|
2018-02-13 02:57:01 -05:00
|
|
|
#define MICROPY_HW_ENABLE_USB (1)
|
2016-02-08 23:36:51 -05:00
|
|
|
|
|
|
|
|
// SD card detect switch
|
|
|
|
|
#if MICROPY_HW_HAS_SDCARD
|
|
|
|
|
#define MICROPY_HW_SDCARD_DETECT_PIN (pin_A8)
|
|
|
|
|
#define MICROPY_HW_SDCARD_DETECT_PULL (GPIO_PULLUP)
|
|
|
|
|
#define MICROPY_HW_SDCARD_DETECT_PRESENT (1)
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
// HSE is 8MHz
|
|
|
|
|
#define MICROPY_HW_CLK_PLLM (8) //divide external clock by this to get 1MHz
|
|
|
|
|
#define MICROPY_HW_CLK_PLLN (384) //this number is the PLL clock in MHz
|
|
|
|
|
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2) //divide PLL clock by this to get core clock
|
|
|
|
|
#define MICROPY_HW_CLK_PLLQ (8) //divide core clock by this to get 48MHz
|
|
|
|
|
|
2018-02-13 02:57:01 -05:00
|
|
|
// USB config
|
|
|
|
|
#define MICROPY_HW_USB_FS (1)
|
|
|
|
|
|
2016-02-08 23:36:51 -05:00
|
|
|
// UART config
|
2016-12-04 20:21:45 -05:00
|
|
|
#define MICROPY_HW_UART1_TX (pin_A9)
|
|
|
|
|
#define MICROPY_HW_UART1_RX (pin_A10)
|
|
|
|
|
#define MICROPY_HW_UART2_TX (pin_D5)
|
|
|
|
|
#define MICROPY_HW_UART2_RX (pin_D6)
|
|
|
|
|
#define MICROPY_HW_UART2_RTS (pin_D1)
|
|
|
|
|
#define MICROPY_HW_UART2_CTS (pin_D0)
|
|
|
|
|
#define MICROPY_HW_UART3_TX (pin_D8)
|
|
|
|
|
#define MICROPY_HW_UART3_RX (pin_D9)
|
|
|
|
|
#define MICROPY_HW_UART3_RTS (pin_D12)
|
|
|
|
|
#define MICROPY_HW_UART3_CTS (pin_D11)
|
|
|
|
|
#define MICROPY_HW_UART4_TX (pin_A0)
|
|
|
|
|
#define MICROPY_HW_UART4_RX (pin_A1)
|
|
|
|
|
#define MICROPY_HW_UART6_TX (pin_C6)
|
|
|
|
|
#define MICROPY_HW_UART6_RX (pin_C7)
|
2016-02-08 23:36:51 -05:00
|
|
|
|
|
|
|
|
// I2C busses
|
|
|
|
|
#define MICROPY_HW_I2C1_SCL (pin_A8)
|
|
|
|
|
#define MICROPY_HW_I2C1_SDA (pin_C9)
|
|
|
|
|
|
|
|
|
|
// SPI busses
|
|
|
|
|
#define MICROPY_HW_SPI1_NSS (pin_A4)
|
|
|
|
|
#define MICROPY_HW_SPI1_SCK (pin_A5)
|
|
|
|
|
#define MICROPY_HW_SPI1_MISO (pin_A6)
|
|
|
|
|
#define MICROPY_HW_SPI1_MOSI (pin_A7)
|
2018-02-13 02:57:01 -05:00
|
|
|
#if MICROPY_HW_USB_HS_IN_FS
|
2016-02-08 23:36:51 -05:00
|
|
|
// The HS USB uses B14 & B15 for D- and D+
|
|
|
|
|
#else
|
|
|
|
|
#define MICROPY_HW_SPI2_NSS (pin_B12)
|
|
|
|
|
#define MICROPY_HW_SPI2_SCK (pin_B13)
|
|
|
|
|
#define MICROPY_HW_SPI2_MISO (pin_B14)
|
|
|
|
|
#define MICROPY_HW_SPI2_MOSI (pin_B15)
|
|
|
|
|
#endif
|
|
|
|
|
#define MICROPY_HW_SPI3_NSS (pin_E11)
|
|
|
|
|
#define MICROPY_HW_SPI3_SCK (pin_E12)
|
|
|
|
|
#define MICROPY_HW_SPI3_MISO (pin_E13)
|
|
|
|
|
#define MICROPY_HW_SPI3_MOSI (pin_E14)
|
|
|
|
|
//#define MICROPY_HW_SPI4_NSS (pin_E11)
|
|
|
|
|
//#define MICROPY_HW_SPI4_SCK (pin_E12)
|
|
|
|
|
//#define MICROPY_HW_SPI4_MISO (pin_E13)
|
|
|
|
|
//#define MICROPY_HW_SPI4_MOSI (pin_E14)
|
|
|
|
|
//#define MICROPY_HW_SPI5_NSS (pin_F6)
|
|
|
|
|
//#define MICROPY_HW_SPI5_SCK (pin_F7)
|
|
|
|
|
//#define MICROPY_HW_SPI5_MISO (pin_F8)
|
|
|
|
|
//#define MICROPY_HW_SPI5_MOSI (pin_F9)
|
|
|
|
|
//#define MICROPY_HW_SPI6_NSS (pin_G8)
|
|
|
|
|
//#define MICROPY_HW_SPI6_SCK (pin_G13)
|
|
|
|
|
//#define MICROPY_HW_SPI6_MISO (pin_G12)
|
|
|
|
|
//#define MICROPY_HW_SPI6_MOSI (pin_G14)
|
|
|
|
|
|
|
|
|
|
// USRSW is pulled low. Pressing the button makes the input go high.
|
|
|
|
|
#define MICROPY_HW_USRSW_PIN (pin_A0)
|
|
|
|
|
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
|
|
|
|
|
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
|
|
|
|
|
#define MICROPY_HW_USRSW_PRESSED (1)
|
|
|
|
|
|
